Answered: What is the smallest capacitor needed… | bartleby

Related questions

Question

What is the smallest capacitor needed in a computer power supply in order to produce at least 3.75 V for 0.31 seconds after the power goes off? Assume that the resistance of all the components of the computer motherboard is 6 Ohms and that the capacitor and motherboard are powered with a 5-Volt power supply.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A 15.0-Ω resistor and a 50.0-Ω resistor in parallel are connected to a 120-V dc source. (a) What is (are) the current(s) through the resistors? current through the 15.0-Ω resistor: A current through the 50.0-Ω resistor: A (b) What is the voltage drop across each resistor? voltage drop across the 15.0-Ω resistor: V voltage drop across the 50.0-Ω resistor: V
A small circuit consists of a resistor in series with a capacitor, as shown. The capacitor stores 79.2 mJ of energy after a ?bat=10.0 V battery has been connected to the circuit for a long time. Then, the capacitor discharges half of this stored energy in exactly1.28 s when the battery is removed and replaced by a ??=1.10×10^3 Ω load. Determine the value of the capacitance C1 in microfarads and resistance R1 in ohms. Please solve for both C1 and R1, thanks!
In the circuit diagram R1 = 5R and R2 = 15R, where R = 14 Ω. The power dissipated in resistor 2 is P = 1.6 W. Part (a) What is the voltage across the battery in volts? Part (b) How much power, Ps, is the source supplying, in watts?
A 4.0-2 resistor is connected to a 12-02 resistor and this combination is connected to an ideal dc power supply with voltage V = 12 volts as shown in the figure. What is the value of current in the 12- resistor? O 1 A O 3 A 12 A O 15 A O 4 A 4.00 www www 1202
The figure below shows how a bleeder resistor (R = 250 kΩ) is used to discharge a capacitor (C = 90.0 µF) after an electronic device is shut off, allowing a person to work on the electronics with less risk of shock. (a) What is the time constant? _______s (b) How long will it take to reduce the voltage on the capacitor to 0.100% of its full value once discharge begins? _______s (c) If the capacitor is charged to a voltage V0 through a 150 Ω resistance, calculate the time it takes to rise to 0.865V0 (this is about two time constants). _______s
You are given the job of evaluating potential power line systems. One system is designed to operate at V = 3000 V, and another would operate at V = 6500 V. Suppose the power line at the higher voltage would dissipate 3 % of the power that it carries. What percentage of the power would be dissipated in the low-voltage power line?
You take a 6.34 V battery, a 226 kQ resistor, and an uncharged capacitor to put together a series circuit. You connect the battery and after 21.2 seconds the current in the circuit has fallen to 61% of its initial value. What is the value of the capacitor in microfarads (µF)? (Enter answer as an integer. Do not enter unit.) A Click Submit to complete this assessment. «< Question 2 of 2
A 15.0-Ω resistor and a 40.0-Ω resistor in parallel are connected to a 120-V dc source. (a) What is (are) the current(s) through the resistors? current through the 15.0-Ω resistor: A current through the 40.0-Ω resistor: A (b) What is the voltage drop across each resistor? voltage drop across the 15.0-Ω resistor: V voltage drop across the 40.0-Ω resistor: V
Two resistors have resistances R1 and R2, where R1 = 2.8R2. When configured in series and connected to a source potential of 23.6 V, they draw 0.723 W of power. If their configuration is changed to be in parallel and the source potential remains the same, what power does the circuit draw