What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 313 mm and an over-all depth of 477 mm? The specified compressive lightweight concrete is 22.2 MPa and the yield strength of stirrups is 333 MPa. The distance of tension reinforcements from the outer fiber of the beam is 59 mm. Round off your final answer in 3 decimal places. Loadings: VDL = 72 kN %3D VLL = 62 kN Axial Tension (DL) = 90 kN Axial Tension (LL) = 19 kN %3D

What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 313 mm and an over-all depth of 477 mm? The specified compressive lightweight concrete is 22.2 MPa and the yield strength of stirrups is 333 MPa. The distance of tension reinforcements from the outer fiber of the beam is 59 mm. Round off your final answer in 3 decimal places. Loadings: VDL = 72 kN %3D VLL = 62 kN Axial Tension (DL) = 90 kN Axial Tension (LL) = 19 kN %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem Solving: A rectangular beam has dimensions of 250 mm by 625 mm with an effective depth (distance from extreme fiber in tension to the centroid of the reinforcing bars) of 575 mm and is reinforced with three 25 mmp. The concrete cylinder strength f.' = 27.6 MPa and the tensile strength in bending (modulus of rupture) is 3.28 MPa. The yield point of the steel is 414.7 MPa. The beam carries a bending moment of 61 kN.m. E_ = 200000 MPa. E_ = 4700,f. Using the transformed area method, determine the stress in the extreme fiber in compression.
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm. Concrete strength is f’c = 28 MPa and steel yield strength is fy = 280 MPa. a. What is the distance of the neutral axis from the top of the beam so that the strain in the concrete 0.003 will be attained at the same time with the yield strain of steel? b. What is the total compressive force on concrete? c. What is the balanced steel ratio?
A group of concrete cubes mixed with different water ratios .. The group with water ratio W / c = 0.3The maximum load was testedFailure causes every cube in the group Required:1- Finding the stress rate for each group in unit N / mm2 with discussing the results and the effect of the water w / c ratio on the compressive strength of the group.
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 300 mm Over-all depth, h = 425 mm Tension reinforcements = 5 pcs 28 mm dia Comp reinforcements = 4 pcs 20 mm dia Specified strength of concrete, f'c = 28 Мра Steel yield strength, fy = 345 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
Help 35 minutes
please answer in the nearest 3 decimal numbers
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.