What is the rule of thumb about the Mach number limit in order that the incompressible flow approximation is reasonable? Explain why wind tunnel results would be incorrect if this rule of thumb were violated.

What is the rule of thumb about the Mach number limit in order that the incompressible flow approximation is reasonable? Explain why wind tunnel results would be incorrect if this rule of thumb were violated.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.70P

See similar textbooks

Related questions

Q: A liquid of density ? and viscosity ? flows by gravity through a hole of diameter d in the bottom of…

A: The relationship of functional variables for the given problem is as follows: The dimensions of all…

Q: Use the Stokes-Einstein equation to estimate the diffusivity (cm^2/s) for a molecule with a solute…

A: Estimate the diffusivity (cm^2/s).

Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 2250…

A: Given data Cycle with two reheat operationsTurbine inlet condition - 2250 psia and 1060°F1st…

Q: An engineer is to design a human powered submarine for a design competition. The overall length of…

A: Given data An engineer is to design a human powered submarine for a design competition. The…

Q: Discuss the use of finite volume methods in computational fluid dynamics.

A: Representation and evaluation of partial differential equations through algebraic equations is…

Q: Which choice is not a scaling parameter used to nondimensionalize the equations of motion? (a)…

A: The kinematic equations of motion with fundamental dimensions are: The dimensional formulas for the…

Q: (b) A wind-tunnel experiment is performed on a small 1:5 linear-scale model of a car, in order to…

Q: • The Expression below of this term Navier-Stokes equation in I given u is is Expression: of the…

Q: Refer Table B-3, "Rayleigh Flow (k=1.4)". For temperature ratio for section 202 = 0.8005, obtain the…

Q: Algebraic equations such as Bernoulli's relation, are dimensionally consistent, but what about…

A: For an equation to be dimensionally consistent, each of the individual components of the equation…

Q: (k-1.33) flows inside a goo conseigat/dhiyeget An ideal wher noz2le under certaiu circumstauces "…

A: The data given is, The area at the inlet, Ainlet = 25 cm2 Inlet Mech number, Minlet = 2.4 Ideal gas…

Q: The output power W. of a spinning shaft is a function of torque T and angular velocity ? . Use…

A: Given Data: The torque acting on the shaft is The angular velocity of the shaft is ω. The output…

Q: A stirrer is used to mix chemicals in a large tank. The shaft power W . supplied to the stirrer…

A: Writing the dimension of the following,

Q: In two dimensional boundary layer, shear stress was changed linearly from the solid surface toward…

A: For setting (1): (i) Write the expression of displacement thickness. δd=∫0δ1-uUdy

Q: A tiny aerosol particle of density ?p and characteristic diameter Dp falls in air of density ? and…

A: The terminal setting speed (V) is a function of diameter (Dp), kinetic viscosity (μ), acceleration…

Q: Q1 : Using Buckingham's method to Express (n) in terms of dimensionless groups. The efficiency (n)…

Q: Write the primary dimensions of each of the following variables from the field of thermodynamics,…

A: Part A) Write the primary dimension for energy.

Q: What are constitutive equations, and to which fluid mechanics equation are they applied?

A: These are the equations which describes the relationship between two physical quantity.

Q: Consider a boundary layer growing along a thin flat plate. This problem involves the following…

A: The boundary layer thickness depends upon the following four parameters: downstream distance, free…

Q: Consider a boundary layer growing along a thin flat plate. This problem involves the following…

A: Boundary layer thickness is the distance between the wall and bulk fluid flow and its dimension is,…

Q: A ship 150 m long, designed to cruise at 18 kn, is to betested in a tow tank with a model 3 m long.…

A: Given: The length of the prototype is LP=150 m. The velocity of the prototype is VP=18 kn. The…

Q: 1. An industrial company operates a steam power plant with reheat and regeneration. The steam enters…

A: Given: P1=P9=115 bar, T1=550oCPcond=P5=P6=0.10 BARP3=P2=30 BarP4=P8=P7=6 Barηadiabatic=0.93 To find:…

Q: An important parameter in fluid flow problemsinvolving thin films is the Weber number (We) which…

Q: A blimp is approximated by a prolate spheroid 90 m longand 30 m in diameter. Estimate the weight of…

A: Given Data: The length of blimp is L = 90m. The diameter of blimp is D = 30 m. Temperature of blimp…

Q: 'hy is it important when assessing indoor air quality to re arameters of the turbulence model as…

A: introduction The structure gives asylum to live and most individuals invest their 85-90% energy…

Q: Select a common dimensionless parameter in fluid mechanics from the following: (a) angular…

A: Given options and To find the dimensionless parameter in fluid mechanics.

Q: Is the Eulerian method of fluid flow analysis more similar to study of a system or a control volume?…

A: The description or analysis of fluid flow is basic learning in the study of hydraulics and fluid…

Q: Can we use the Buckingham pi theorem to prove that the Froud number is dimensionless? Could someone…

A: yes, we use the Buckingham pi theorem to prove that the Froud number is dimensionless

Q: A 5 m of ship model is towed in the water of kinemetic viscosity 1x10^-6 m^2/s at 3.5 m/s. The…

Q: Show that cot?t+ tan?t= 1is a possible form for the boundary surface of an incompressible flow when…

A: For a 2-D incompressible steady flow to be possible it has to satisfy the continuity equation for a…

Q: Help me solve this problem A uniform air stream of Ma corner as shown in figure. T stream are 223 K…

A: as per our guidelines i solved 1st 3 questions

Q: A correlation of computational fl uid dynamics results indicatesthat, all other things being equal,…

Q: Briefly explain the advantages of using the Von Karman Approx n determining the boundary layer…

A: The Von Karman approximation makes it simple to find boundary layer parameters, and the benefits are…

Q: What role does computational fluid dynamics (CFD) play in optimizing the design and performance of…

A: Computational Fluid Dynamics (CFD) is a branch of fluid mechanics that uses numerical analysis and…

Q: • By using dimensional analysis, develop a non-dimensional relation between the shear stress and the…

Q: the differential equation for conservation of mass, the continuity equation. In cylindrical…

A: given steady flow equation 1r∂rur∂r+1r∂uθ∂θ+∂uZ∂Z=0

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

One of the conditions in using the Bernoulli equation is the requirement of inviscid flow. However there is no fluid with zero viscosity in the world except some peculiar fluid at very low temperature. Bernoulli equation or inviscid flow theory is still a very important branch of fluid dynamics for the following reasons: (i) (ii) There is wide region of flow where the velocity gradient is zero and so the viscous effect does not manifest itself, such as in external flow past an un- stalled aerofoil. The conservation of useful energy allows the conversion of kinetic and potential energy to pressure and hence pressure force acting normal to the control volume or system boundary even though the tangential friction stress is absent. It allows the estimation of losses in internal pipe flow. (A) (i) and (ii) (B) (i) and (iii) (ii) and (iii) All of the above (C) (D)
Select a common dimensionless parameter in fluid mechanics from the following: (a) angular velocity; (b) Kinematic viscosity; (c) specific volume; (d) specific weight; ( e) none of these answers
In the study of turbulent flow, turbulent viscous dissipation rate ? (rate of energy loss per unit mass) is known to be a function of length scale l and velocity scale u′ of the large-scale turbulent eddies. Using dimensional analysis (Buckingham pi and the method of repeating variables) and showing all of your work, generate an expression for ? as a function of l and u′.
When a flow is considered incompressible what assumption is being made regarding fluid properties? The answer was: Density is assumed to remain constant I want to know why is this the answer?
(k-1.33) flows inside a goo conseigat/dhiyeget An ideal wher noz2le under certaiu circumstauces " the cross-sedtiou of the noz2le is 2s cu?, Mace nuuber is 2.4. What is the cross-seetion where Mach uuuber = 3.5 - 3. %3D - /1
Using primary dimensions, verify that the Rayleigh number is indeed dimensionless. What other established nondimensional parameter is formed by the ratio of Ra and Gr?
Is the Lagrangian method of fluid flow analysis more similar to study of a system or a control volume? Explain.
Mott ." cometer, which we can analyze later in Chap. 7. A small ball of diameter D and density p, falls through a tube of test liquid (p. µ). The fall velocity V is calculated by the time to fall a measured distance. The formula for calculating the viscosity of the fluid is discusses a simple falling-ball vis- (Po – p)gD² 18 V This result is limited by the requirement that the Reynolds number (pVD/u) be less than 1.0. Suppose a steel ball (SG = 7.87) of diameter 2.2 mm falls in SAE 25W oil (SG = 0.88) at 20°C. The measured fall velocity is 8.4 cm/s. (a) What is the viscosity of the oil, in kg/m-s? (b) Is the Reynolds num- ber small enough for a valid estimate?
A 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.
The drag of a sonar transducer is to be predicted, based on wind (Air) tunnel test data. The prototype is 1.5 m diameter sphere, is to be towed at 4.3 m/s in seawater. The model is 0.2 m diameter. Take: Air density = 1.2 kg/m, Air dynamic viscosity = 1.81 x 10$ Pa. s, seawater density = 1000 kg/m, seawater dynamic viscosity 1.813x 10 Pa s, If the drag of the model at these test conditions is 9.5 N, estimate the drag of the prototype in (N).
In CFD lingo, the stream function is often called a non-primitive variable, while velocity and pressure are called primitive variables. Why do you suppose this is the case?
PLS SHOW ME FULL STEPS SIR PLS ANSWER WITHIN 30 MIN SIR SUBJECT (FLUID MECH 2)