What's number 2 46.8.9.10111213141516QUESTION 1What is the RMS value of an AC voltage that has a 347 V peak?a. 245.3b.490.6с. 265.7d.469.3QUESTION 2What is the peak value when an RMS voltage is 245 volts?a. 346.43Ob. 173.2с. 396.5d. 189.4QUESTION 3

What is the RMS value of an AC voltage that has a 347 V peak? O a. 245.3 b.490.6 C. 265.7 d. 469.3 QUESTION 2 What is the peak value when an RMS voltage is 245 volts? a. 346.43 b. 173.2 Oc. 396.5 d. 189.4

What is the RMS value of an AC voltage that has a 347 V peak? O a. 245.3 b.490.6 C. 265.7 d. 469.3 QUESTION 2 What is the peak value when an RMS voltage is 245 volts? a. 346.43 b. 173.2 Oc. 396.5 d. 189.4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1/ Identify the signal processor from the below following. a. Strain Gauge b. Piezoelectric Accelerometer c. Thermistor d. Wheatstone Bridge
THREE PHASECONTROLED RECTIFIER It is used to feed a physical load which is resistance of 6 ohm And inductive impedance high enough for the current to be continuous and free from vibrations and the THREE PHASECONTROLED RECTIFIER is connected to delta and his voltage 100 volt , What is the value of the power drawn from the source if the ignition angle is 45 degrees?
Calculate the following a) V1 [1 b) i c) i2 Q17 The half wave rectifier is supplied with 230V, 70HZ signal. Assume the number of turns in the primary to secondary ratio is 7:2. i) Calculate the average de current through the load resistor 3KQ. Calculate the value of input ac power, output de power. 18. For the circuit shown in Figure B18, Vcc = 18 V, B = 110, Rc = 4.7 kQ and RB that VBE=0.7 V. 450 k2, assum %3! Vcc | Ic Ro RB Vc VCE
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
Please answer all subparts
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
Please answer in typing format
Please answer in typing format solution please only typing format Please I will like it please Thanks in advance
Input voltage applied to a half wave rectifier is V= 100 cos (150 t). The maximum current through 5kO load resistor is calculated as O a. 10mA O b. 20A O C. 20mA O d. 75mA Next pa Previous page Final exam Descriptive Answer she -Electronics 1 ► Jump to... Forum ciull lis hp
Please answer both subparts and choose one option and explain in short dont copy
As for the types of rectifiers. We basically have three types of rectifier typologies or schemes. Look at the figure and answer, what are these types in sequence: Respond like this: Fig 1: Rectifier ____, Fig 2: Rectifier ____, Fig 3: Rectifier ____.
Figure Q1 (a) showed full wave rectifier. The step-down transformer has turn ration 9:1. Cut in voltage for diode is 0.7V, and R₁ = 105 Q. Calculate (i) Output load voltage, Vo. 9:1 A 110V 60Hz B D₁ D. D₂ ↑ D.C. O/P