Answered: What is the reaction at C in kips. In…

What is the reaction at C in kips. In Figs. P14.1–P14.4 using the method of consistent deformations. Absolute value with two decinal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a) List four different methods that could be used to determine the reactions for the statically…

A: a) Four methods which can be used to determine the reactions for the given statically indeterminate…

Q: 333 of o, and a, if the principal stresses are known to be 20 MPa and -80 935. For the element shown…

Q: Determine the reactions and draw the shear and bending moment diagrams for the beam using the method…

A: The values given in the question are as follows

Q: Q2) At a point in a structure subjected to plane stress, the stresses are shown in Fig. 2a. A stress…

Q: Q1: Determine the reactions of the truss shown in Fig, using the method of consistent deformations.…

A: Given -

Q: F 1-87 The steel swivel bushing in the elevator control of an airplane is held in place using a nut…

A: Given Maximum shear stress=21 ksi Average normal stress = 60 ksi d=Diameter of washer=0.75 in…

Q: 1. Determine the reactions and the force in each member of the truss shown in Fig. below by the…

A: External SI = R-r = 0Internal SI = (m+r)-2j = 1Hence, 1 Internal redundant needs to be…

Q: Find the strain Change in length =0.04 mm Initial length=1000 mm

Q: Question 4 A structural component has a W-shaped cross section and is acted upon in its plane of…

Q: - Permanent deformation takes place after Yield point Select one: True False

A: True

Q: 1. Determine the reactions and the force in each member of the truss shown in Fig. below by the…

Q: Determine the support reactions for the structures shown in figure by using the method of consistent…

A: The structure is having structure indeterminacy 1. Taking redundant as RB . So, the moment in…

Q: In a laminar boundary layer over a flat plate the ratio of shear stresses T, and T2 at two T₂…

A: Given data- Laminar boundary layer over a flat plate- Distances from the leading edge- x2 & 3x1,…

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

Q: QUESTION 1 Determine the reactions and draw the shear and bending moment diagrams for the structure…

Q: Q-2 Use the method of consistent deformations to determine the reaction components, and draw the…

Q: Prob. 2.12-9. (a) Using Figs. P2.12-9 and the definition of extensional strain given in Eq. 2.35,…

Q: Q-1 Use the method of consistent deformations to determine the reaction components, and draw the…

Q: Use the method of consistent deformations to determine the reaction components, and draw the shear…

Q: (b-8b)+ (d-8d) P 14 Fig. 1.5 L + ÖL 1.9.1. For One-Dimensional Stress System. The relationship…

Q: Determine the reactions and draw the shear and bending moment diagrams for the structures shown in…

A: Find degree of static indeterminacy, DS DS = (3m +R)-(3j+A) Where m= number of members R = number…

Q: Q2: Determine the state Of stresses at point A on the cross section of the beam shown in Fig. at…

Q: Determine the reactions and draw the shear and bending moment diagrams for the structures using the…

Q: Determine the reactions and draw the shear and bending moment diagrams for the beams shown in Figs.…

A: Solution;

Q: true or false 5.When analyzing a structure by the method of consistent deformations, we can choose…

Q: For the state of plane stress shown in Fig. , determine (a) the principal planes, (b) the principal…

A: First we summarise the given data : To find : a ) The principal planes b ) The principal stresses…

Q: d normal strain (Ex-x) at section X-X. hear strain (yx-x) at section X-X. nodulus of steel are, E, =…

A: cos 45 =12θ= tan-143= 53.15° component of reaction R1& R2 in x & y…

Q: The critical resolved shear stress for a metal is 24 MPa. Determine the maximum possible yield…

Q: Problem 1.5. The safe stress, for a hollow steel column which carries an axial load of 2.1 x 10³ kN…

Q: Q-1 The continuous beam ABC, Fig.1, is hinged at A and roller supported at B and C, and is subjected…

Q: Use the method of consistent deformations to determine the reaction components, and draw the shear…

A: Indeterminate beam having 2 spans AB and BC UDL of intensity 'w' acting in span AB

Q: Determine the reactions and the force in each member of the truss shown in Fig. 13.6(a) using the…

A: Given truss: E=29000 ksi

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

What is the reaction at C in kips. In Figs. P14.1–P14.4 using the method of consistent deformations. Absolute value with two decinal places.

75 k
2 k/ft
A
B
F15 A+15 A-
30 ft
37
I
E = constant
AG. P14.3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The assembly in Fig. P-242 consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. A 0.75 m O Steel A = 250 mm² E = 200 GPa 1.5 m Figure P-242 Aluminum L = 2 m A = 300 mm² E = 70 GPa B
A plane element removed from a thin-walled cylindrical shell loaded in torsion is subject to the shearing stresses shown in Fig. 3-20. Determine the principal stresses existing in this element and the directions of the planes on which they occur. Ans. 50 MPa at 45° 50 MPa 50 MPa 50 MPa 50 MPa
(b-8b)+ (d-8d) Fig. 1.5 L + ÖL 1.9.1. For One-Dimensional Stress System. The relationship between stress and strain for a unidirectional stress (i.e., for normal stress in one direction only) is given by Hooke's law, which states that when a material is loaded within its elastic limit, the normal stress developed is proportional to the strain produced. This means that the ratio of the normal Lateral strain Poisson's ratio, u = Longitudinal strain Lateral strain = u x Longitudinal strain Problem 1.5. The safe stress, for a hollow steel column which carries an axial load of 2.1 x 10³ kN is 125 MN/m². If the external diameter of the column is 30 cm, determine the internal diameter.
Prob. 2.9-10. At room temperature (70°F) and with no axial load (P = 0) the extensional strain of the prismatic bar (Fig. P2.9-10) in the axial direction is zero, that is, € = 0. Subsequently, the bar is heated to 120°F and a tensile load P is applied. The material properties for the bar are: E = 10 × 10³ ksi and a = 13 x 10-6/F, and the cross-sectional area of the bar is 1.8 in². For the latter load-temperature condi- tion, the extensional strain is found to be €x = 900 × 10 6. (a) Determine the value of the axial tensile load P. (b) De- termine the normal stress and the shear stress on the oblique plane NN'. (Note: The total strain is the sum of strain asso- ciated with normal stress o (Eq. 2.14) and the strain due to change of temperature AT (Eq. 2.8).) in. P Gage measures extensional strain Ex N N' 25° P2.9-10 X
EXAMPLE 4.1 Determine the deformation of the steel rod shown in Fig. under the given loads (E = 200000000 kN/m²) 600mm2 200mm2 100 kN 300kN 200kN 0.4m 0.3m 0.3m
Q-2 Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.2. (EI is constant). 20 KN 10 KN B 2 m D et 2 m Fig.2
Q1: Due to the applied loading, the element at point A on the solid shaft in Fig.a is subjected to the state of stresses shown in Fig. b. Determine the principal stresses and maximum shear stresses acting at this point. Draw the element at each state of stresses. P Fig. a T 45 MPa <-30 MPa Fig. b 10 MPA
6. In Fig. 6, a 1.5 m long cantilever beam with a circular cross section (R = 100 mm) and two symmetrically positioned longitudinal holes is loaded by a concentrated force P at its tip. The material is a titanium alloy with a 600 MPa maximum allowed working stress when bent. Find the maximum permitted vertical force P value. 1.5 m Radius= R = 100 mm Radius of hole =
Refer to the composite body shown in Figure IV.a) Solve for the reactions at pin support at A and roller support at B. b) Determine the reactions at each connection- B,C,D.
PAGE:. DATE :.. A rectangular lot steei tape which was later found to 5 mm too short. The recorded dimensions was mearured uring a be 121.5m long by 92:5m wide. What ir the Were error in the area
An aluminum bar having a cross-sectional area of 160 square millimeters carries the axial loads at the positions shown in the figure. Assume that the bar is suitably braced to prevent buckling. E = 70 GPa. 35 KN 15 KN 30 KN 10 KN -> 0.8 m 1.0 m 0.6 m B FIGURE 9 Determine the deformation at segment AB Determine the deformation at segment BC. Determine the deformation at segment CD. Determine the total deformation of the bar.
2. Determine the reactions and draw the shear and moment diagrams for the structures shown using method of consistent deformations. 37 k 3 k/ft ..... 10 ft 5 ft 20 t El = Constant 12 kN/m 23 kN BO 20 ft 15ft El = Constant