Answered: The critical resolved shear stress for…

The critical resolved shear stress for a metal is 24 MPa. Determine the maximum possible yield strength (in MPa) for a single crystal of this metal that is pulled in tension. i MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: why is P positive for stress A

A: The compressive stress is considered as positive and tensile stress is considered as negative.

Q: A straight wire 15 m long is subjected to tensile stress of 2000 kgf/cm². Elastic modulus is 1.5x106…

A: We have to calculate the temperature change to produce the same elongation

Q: Which of the following best describes distortion energy? A.Work done on an element by a force which…

A: Answers : 1) C . Distortion energy is the energy stored in a material due to change ain its shape.…

Q: strain in the plane of maximum shear strain is

A: Given data, Biaxial normal tensile strains of an element is,⇒ 0.0030 and 0.0020. Find normal…

Q: An assembly of a material consists of a brass shell fully bonded to a ceramic core. The brass shell…

Q: At a point in a strained material, tensile stress of 100 MPa and compressive stress of 60 MPa are…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: - Permanent deformation takes place after Yield point Select one: True False

A: True

Q: If 8, is the thickness of laminar boundary layer at a distance x, from the leading edge of the flat…

Q: The slope of the stress-strain curve in the elastic deformation region is

A: The given question asked here is the slope of the stress-strain curve in the elastic deformation…

Q: This is a determinate O Primary Structure O Virtual System Real Cus Dool Sustom

Q: The value of strain if stress is 35 MPa and Youngs modulus 65 MPа

A: The given question is related with solid mechanics . In this question we are provided with value of…

Q: A prismatic bar has a cross-section of 25 mm by 50 mm and a length of 2000 mm. Under an axial load…

A: →Cross section Area of prismatic bar A= Breadth×Depth=25×50mm→Length L=2000mm→Axial load…

Q: The shear strength parameters scaled off mohr's circles in lab 5 were 27° and 16 kPa. Compute the…

A: ϕ = Angle of internal friction = 27°c = Cohesion = 16 kPaσc = σ3 = Cell pressure = 304 kPaTo find…

Q: a) Draw the corresponding crystallographic planes and directions with respect to the applied stress…

A: Given data : Stress is given as 100 Mpa Solutions are :

Q: In a laminar boundary layer over a flat plate the ratio of shear stresses T, and T2 at two T₂…

A: Given data- Laminar boundary layer over a flat plate- Distances from the leading edge- x2 & 3x1,…

Q: Determine the total strain in the bar shown in Figure 2.

A: Find load at Distance xat L=0 load =3qoat L=L load =0at x=?3qo-00-L=qx-0x-Lqx=3qox-LLload at…

Q: At an axial load of 22 kN, a 15-mm-thick x 35- mm-wide polyimide polymer bar elongates 4.6 mm while…

A: Given, L = 315 mm B = 35 mm Thickness = 15 mm Load = 22 kN Length elongation = 4.6 mm With…

Q: A wire of circular cross-section of diameter 1.0 mm is bent into a circular arc of radius 1.0 m by…

A: Given- Diameter d=1 mm, Radius of arc R=1 m, E=100 GPa, It is needed to find the value of the…

Q: An assembly of a material consists of a brass shell fully bonded to a ceramic core. The brass shell…

A: Given Data:Outside dia of brass shell=75mmInside dia of brass shell = 45mmTemperature =…

Q: A body is subjected to stresses as shown in the figure given below. 90 MPa 35 MPa →145 MPa The FOS…

A: Given- State of stresses given as shown in the figure- σx=145 MPa,σy=90 MPa,τxy=35 MPa, Yield…

Q: I am still confused with the sign convention we were told that in rock mechanic the sigma y in…

A: This question is related to the Stresses transformation from Strength of the material from Civil…

Q: A 12 mm diameter rod has an axial strain of 0.0009. If the metal rod has a Poisson's Ratio of 0.25,…

Q: the strain on the Z axis is -0.1748 mm/mm . Height of structure is : H=8 cm=80 mm Length is : L=4…

A: Given data, Strain in Z direction is -0.1748 mm/mm

Q: A steel rod 15 m long is at a temperature of 15°C. The values of a = 12x10-6/°C and E=200GN/m² are…

A: Given- Length of the rod L=15 m, Temperature raised from 15 degrees to 65 degrees. Coefficient of…

Q: A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a…

A: Determine the modulus of elasticity of gold,Eg=?

Q: If temperature of liquid increase by 3 unit the surface tension A increase by 3unit B decrease by…

A: given- The temperature of the liquid is increased by 3 units. It is needed to find the change in…

Q: A structural component in a fighter jet aircraft has a cellular cross-section (Fig. Q1). The…

A: Given,Torsional load, T = 40 Nm = 40×103 NmmModulus of rigidity, G = 30 GPa = 30×103 MPa = 30×103…

Q: he maximum principal stress for the stress state shown in the figure is O

A: Given:σx=σσy=στxy=σ

Q: Consider a single crystal oriented such that the slip direction and normal to the slip plane are at…

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to…

A: Given- Poisson's ratio- μ=0.5, Volumetric strain = ?

Q: on, a line element What is the perce

Q: Tim In the yielding region, what happens if the stress is removed? O a. The material does not return…

Q: In a steel railroad, the 12 meters long rails are laid with a clearance of 5 mm at a temperature of…

A: solution the length of steel rod L =12mts clearance gap ∆=5mmE=200Gpa=200×1000 Mpa a for linear…

Q: 2. For the Kelvin representation of the Standard Solid Model, what is the maximum strain achievable…

A: Solution: As per the question:

Q: A thin-walled circular tube and a solid circularbar of the same material (see figure) are…

A: Given:- The torsion is applied to the circular tube and a solid circular bar The material of both…

Q: Question- A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile…

A: Tensile stress Stress in y-direction Shear stress To Find-The value of the maximum normal stress.

Question

The critical resolved shear stress for a metal is 24 MPa. Determine the maximum possible yield strength (in MPa) for a single crystal of
this metal that is pulled in tension.
i
MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

21 The volume coefficient of thermal expans ion is equal to two times the value of area coefficient of expansion.( O True 22 False The deformation aLAT, is the deformation when material is exposed to temperature increase or decrease. ( True O False
The degree to which the theoretical value of stress concentration is actually reached is called as
An element in uniaxial stress is subjected to a tensile stress of 49 MPa in the x – direction. Determine the stresses acting on an element oriented at an angle of – 27 °C from the x – axis (clockwise direction)
A single zinc crystal is loaded in tension with the normal to its slip plane at 60° to the tensile axis and the slip direction at 40° to the tensile axis. a) Calculate the resolved shear stress when a tensile stress of0.69 MPa is applied. b) What tensile stress is necessary to reach the critical resolved shear stress of 0.94 MPa?
19 This theory explains that the elastic failure occurs when energy per unit volume in a strained material reaches the value of the strain energy per unit volume at the elastic limit point in the simple tension test. Also, the maximum energy which a body can store without deforming plastically is constant for that material irrespective of the manner of loading. What do you call this theory Bulk Modulus Volumetric strain Hook's Law Elastic Theory Strain energy theory
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 250-mm-gage length. Using E = 110 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.