What is the purpose of the Crankcase Ventilation system?

Q: What are the three main types of hoods?

A: In this question we will define the hood and writes it's type.

Q: A vehicle has had several radiator replacements, and each time there has been pinhole leaks in the…

A: Solution:

Q: What is the importance in using a metal as the material for the exhaust gasket? Metal was chosen to…

A:

Q: Question: How can we change the pressure valve of the hydraulic transmission system?

A: A hydraulic power transmission system uses a pressured flow to transport the energy needed to…

Q: Technician A states that the vehicle may be overheating becuase the heater control valve is stuck…

A: Technician A is saying correct statement.

Q: The diesel engines operates with low pressure than petrol engine a. FALSE b. TRUE

A:

Q: How is the maintenance of a multi-piston cylinder different from regular cyli

A: Leakage losses is low in multi-piston cylinder so efficiency is high in it . Multi-cylinder give…

Q: Fin Fan air Cooler must be flat and horizonal position during preservation time for what any…

A: A fin air cooler, also known as a fin addict cooler or air fin cooler, is a type of heat exchanger…

Q: How many compression ring and oil ring a IC engine piston will have? a. 2 compression ring and 1…

A: Piston of internal combustion engine have three rings for each cylinder. Top two rings are called…

Q: Which of the following is not measured with a feelergauge set?a. Piston ring side clearanceb.…

A: A feeler gauge is a tool used t measure the gap widths and clearance    A feeler gauge is used for…

Q: The Single Stage Two Speed Supercharger and its Operation

A: To Explain:  The single stage two speed supercharger and its operation :  Concept used: Single stage…

Q: Which one of the following mechanisms is used to control the rotor speed of the wind turbine?…

A: Objective: To determine the mechanism used to control the rotor speed of the wind turbine.

Q: What are the advantages and disadvantages of the engine lubrication

A: The lubrication system's job is to provide oil to moving parts in order to minimise friction…

Q: What prevention measures would the student take to prevent fluid overload?

A: given; What prevention measures would the student take to prevent fluid overload?

Q: What should be done to prevent excessive deposits and buildup within the cooling system? Select one:…

A: Objective: To select which of the given options are used to prevent excessive deposits and buildup…

Q: What precaution should you take to prevent hydraulic injection?

A: Some precautions to be taken to avoid hydraulic injection are, When the hoses or hydraulics are…

Q: Choose the correct statement. Select one: a. A dry sump system stores oil in a tank outside of the…

A: The wet sump system  is the best fit during aggressive driving conditions.

Q: Before installing the crankshaft, what should you spray onto the bearings?

A: Before installing the crankshaft the chemical treatment by using oil and grease is required to be…

Q: Chaper 32 question 2 What can be used to check for leaks on the presure side of a turbocharger…

A: The leaks from the turbocharger of air can occur both on the vacuum side, one is air intake to the…

Q: A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling…

A: Given :-  A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and…

Q: Which component allows the vehicle to maximize engine torque? A- Torque converter  B- Differential…

A: Option A is correct.

Q: What happens to the engine due to high temperature ?

A: Engine: It is a mechanical device which is used to convert chemical energy of the fuel into…

Q: 52) Technician A says few production vehicles have transmissions with an internal oil cooler.…

A: Technician A is saying correct statement as the transmissions with the oil cooler are located in the…

Q: What is/are the manufacturing process(es) for the crankshaft? Casting and secondary machining Deep…

A: Explanation: The crankshafts are mainly manufactured by using forging. The casting and machining are…

Q: Technician A says that all transmission opening pressure are derived from the regulated output flow…

A: Technician A says that all transmission opening pressure are derived from the regulated output flow…

Q: The connecting rod journal is also called the __ .a. balancer shaftb. vibration damperc.…

A: Analysis indicates that the connecting rod journals are those that are attached to the large end of…

Q: A reddish-colored oil is discovered to be leaking during an engine oil change and inspection:…

A: Leak fluid color and its use in an automobile is shown in tabulated form Leak fluid color  fluid…

Q: Types of engine oil

A: There are mainly three types of engine oil  1. Full Synthetic engine oil 2. Mineral engine oil  3.…

Q: d. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to…

A: 19. if the main wire (coil) to the distributor and the coil to the switch are broken , replace them…

Q: Carburetor icing, icing on air intakes and any icing that affects the powerplant operation of an…

A: Induction icing is correct answert

Q: what is the component that is moving to allow fuel to be injected into the intake port

A: A carburetor allow fuel to be injected into the intake port.

Q: the number one cause of clutch disc failure

A: Clutch :- The function of a clutch is to transmit the power from rotating shaft or motor or engine…

Q: The piston top surface is generally flat in the indirect injection  True False

A: Given: The piston top surface is generally flat in the indirect injection

Q: What component is responsible for circulating coolant through the engine

A: In the engine we use water pump to force the water to circulate throughout...

Q: Technician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician…

A: The turbocharger is a device used to increase the power of the engine by compressing the air that…

Q: A vehicle is having its water pump replaced. When the water pump is removed, severe corrosion is…

A: A vehicle is having its water pump replaced. When the water pump is removed, severe corrosion is…

Q: What could be the problem when the vehicle’s domelight dims when a power seat is moved?

A: Circuit and fuses are impacted. The vehicles have three different types of dome lights. a. Door dome…

Q: What is combustion chamber

A: Given Data : combustion chamber

Q: The bolt size of cylinder head in a reciprocating compressor is _____ a. M20 b. M16 c. M24…

A: As it has a trend to fatigue failure in Reciprocating Compressor... So, we need higher sized bolt...

Q: Describe an acceptable storage area for a cylinder offuel gas.

A: Storage cylinders are used for the storage of the fuel gases. These cylinders are made up of iron or…

Q: The presents  of air in the cooling systems indicates the head gasket is faulty? True or false

A: The given statement is true.

Q: knocking

A: When fuel burns unevenly in your engine's cylinders, knocking happens. Fuel will burn in discrete,…

Q: Which of the following statement is correct according to the Wind Energy Conversion System? O a. Low…

A: The correct answer to the above question is option (a).  The low-speed high torque shaft is…

Q: The misfiring exceeds  ____________ to  ____________ percent in a ____________ rpm period if Type B…

A: Unburned hydrocarbons are produced by misfires, which puts more strain on the catalytic…

Q: systems used in engines? 2 types case

A: There are typically two types of crankcase ventilation systems used in engines: the positive…