What is the proeutectoid phase for an iron-carbon alloy in which the mass fractions of total ferrite and total cementite are 0.90 and 0.1, respectively? See Animated Figure 9.24 Part 1 What are the concentrations of carbon in a-ferrite and FegC at a temperature just below 727°C? You may want to use Animated Figure 9.24. (a) Ca = i wt% (b) CFe,C i wt% Attempts: 0 of 3 used Submit Answer Save for Later Part 2 Compute the composition of an iron-carbon alloy for which the mass fractions of total ferrite and total cementite are 0.90 and 0.1, respectively. Co wt% C

What is the proeutectoid phase for an iron-carbon alloy in which the mass fractions of total ferrite and total cementite are 0.90 and 0.1, respectively? See Animated Figure 9.24 Part 1 What are the concentrations of carbon in a-ferrite and FegC at a temperature just below 727°C? You may want to use Animated Figure 9.24. (a) Ca = i wt% (b) CFe,C i wt% Attempts: 0 of 3 used Submit Answer Save for Later Part 2 Compute the composition of an iron-carbon alloy for which the mass fractions of total ferrite and total cementite are 0.90 and 0.1, respectively. Co wt% C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the copper silver phase diagram below. 100g of a 40 wt% Cu 60 wt% Ag alloy is made and cooled from liquid form. a. At what temperature does the solid phase start to appear? b. What phases exist at 780°C? c. What are the compositions (Cu and Ag%) of the phases in question b? d. What are the weights (in g) of Cu in the solid phase and liquid phase in question b?
do not provide wrong solution
According to the following graph, two samples of 1080 steel are cooled from the eutectoid temperature, one at a cooling rate of 250°C/s and the other at a cooling rate of 7.27x10-8 °C/s. Specify the phases obtained and explain their formation from thermodynamic and kinetic perspectives. Also, briefly describe their formation. Draw the microstructure of the phases obtained. Sıcaklık (C) 800 700 600 500 400 300 200 100 0 10 1 T M(başlama) M(% 50) M(% 90) 10 M+O -Otektoid Sıcaklık 10² Zaman (s) % 50 10³ 104 105
1. Specify all temperature-compositicn points at which eutectics, eutectoids and peritectics. At 700 degrees Celsius and composition of 20% by weight of copper, calculate the compositions by fraction of each phase for copper? 1700 1500 L. 1300 1100 900 TiCu- 700 Ti:Cu4 500 20 40 60 (Ti) Composition (wt% Cu) to (0o) anjesedwa
cover the manufacturing and loading of an NiCu bar. The bar has a 0.01 m x 0.01m cross-section and is 1m long. The alloy is 60% (at%) Ni and 40% (at%) Cu.
A 50 wt% Pb-50 wt% Mg alloy is slowly cooled from 700 °C (1290 °F) to 400 °C (750 °F). (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase? Temperature (°C) 700 600 500 400 300 200 100 2 0 0 (Mg) 560°C First solid (21 wt% Pb) α 20 465°C 5 a + L Composition (at% Pb) 40 10 L a + Mg₂Pb 20 60 Composition (wt% Pb) Last liquid (67 wt% Pb) 30 Mg₂Pb 40 T T L + Mg₂Pb M 18 80 L + Mg₂Pb 70 100 B B+ Mg₂Pb T B + L D T 1200 1000 800 600 400 200 100 (Pb) Temperature (°F)
3- It has been determined that the microstructure of a steel consists of 80% pearlite and 20% ferrite. What is the C concentration of this steel? Explain by calculating
Identify the microstructures of each of expected to be found in each of these alloys 1095 furnace cooled from 1650 farenheight 1095 air cooled from 1650 farenheight 1095 water quenched from 1650 farenheight
Consider a Fe-0.5% C alloy. What is the amount of pro eutectoid phase (in percentage ) just above the eutectoid temperature
Which of the following alloys would form a complete substitutional solid solution? O Metal 1 is HCP, metal 2 is FCC, and atomic radius difference is less than 15%. O Metal 1 is BCC, metal 2 is BCC, and atomic radius difference is at least 15%. O Metal 1 is FCC, metal 2 is FCC, and atomic radius difference is 12%. O Metal 1 is BCC, metal 2 is FCC, and atomic radius difference is 12%. O Metal 1 is FCC, metal 2 is FCC, and atomic radius difference is 15%.
In the present figure: compare between the alloy number 1 (0.4% C) and 2 (1.2% C) regarding: A. The expected mechanical properties of the two alloys (with explanation). B. The range of applications for these alloys. C. The stages of annealing treatments including: 1) Softening 2) Spheroidizing 3) Grain Size Reducing.. Subject: Metallurgy