What is the mechanical advantage of a 1/4" diameter screw with 20 threads per inch?

Q: Find the pitch for an internal thread, if the depth of thread is 0.5 mm. Pitch (in mm) =

A:

Q: Give 1 example of methods of joint

A:

Q: Define the term distributing force?

A: Distributing force:- Distributing Force is the force acting on the body over a length or surface.…

Q: I need answers to parts 10, 11, and 12, pertaining to the print provided.

A: Hii,thanks for the question but there is only 10th  question so we are answeering only 10th…

Q: Power is transmitted from the 1st shaft to the 2nd shaft with a Conical Friction coupling at 950…

A: Given: The speed of coupling, N = 950 rpm The taper angle, α = 25° The mean diameter, D = 120 mm

Q: gonal nuts Ior b.25mm diameter bolts nave a neight oI_5.5mm. II uhe ulumate trength of the nut…

A: Givend=6.25mmh=5.5mmςmax=103MpaFos=5

Q: clearance in the assembly

A: Given; In an interchangeable assembly, shafts of size = 25.00-0.0100-0.040mmsizes of  holes=…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: How to calculate the threaded hole axial shear strength of an aluminum 7075 1 inch thick plate. The…

A: Step 1: Given: Material Properties:Aluminum 7075 shear strength: 38000 psi (typical value)Thread…

Q: Draw the assembly views of the following G Clamp from a front view and top view. Provide a standard…

A: To Draw the assembly views of the following G Clamp from a front view and top view.

Q: Find Pitch(in mm) , if Minor diameter is 27 mm and Nominal diameter is 33 mm for an internal thread.…

A: Given: Dnominal=33 mm Dminor=27 mm To Find: Pitch

Q: Don't Copy any wrong solution, Solve it fast within 20-30minutes. 1) A double threaded power screw…

A:

Q: Thread Fits and 7. Define fit, allowance, tolerance, and limits. Classifications

A: Topic : engineering drawing

Q: pieces of sheet metal are to be u-formed using a single-acting cylinder. the start signal is to be…

A: The problem involves a single-acting cylinder that is used to U-form pieces of sheet metal. The…

Q: Required information For a bolted assembly with eight bolts, the stiffness of each bolt is kb = 0.8…

A: Kb = 0.8 MN/mm Km = 2.6 MN/mm no.of bolts N = 8 M6 x 1 class 5.8 bolt   From the standard bolt data…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: 7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative…

A: (a) Write the given data. Tf=48Df=10.5 inTs1=30Ts2=26Ts3=23Ts4=20Ts5=16Ts6=12Nf=105 rpmFf=28 lb

Q: Anonymous answered this 221 answers a. area of wheel = pi*R² area of 6 cutouts = 6*pi*(R/5)² =…

A: Area of wheel= pi*R^2  Area of 6 cutouts= 6*pi*(R/5)^2 = 0.24*pi*R^2

Q: 7. Pitch 8. Length of threads 11. Pitch 16. Pitch

A: Standard designation for Metric thread

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: For each of the structures shown in Fig.2, sketch the following: i. Free body diagrams showing the…

A: Given: FA = 300 lbf FB = 750 lbf

Q: What size UNF bolt made from SAE grade 5 steel is needed to carry a static tensile load of 3000lb…

A:

Q: Advantages and disadvantages of using smaller bolts than bigger bolts

A:

Q: A bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain…

A: d=14 mm

Q: 15-1 Compare the tensile load capacity of a 5/16-18 UNC thread and a 5/16-24 UNF thread made of the…

A: The tensile load capacity is the product of the tensile stress and the cross-section area. As the…

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Q: each part A -  A weight of 1500 N must be lifted. What is the total required torque necessary to…

A:

Q: Bolt properties: M12 x1.75 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size.…

A:

Q: (a) Find Depth of cut and Root diameter for M18 x 2.75 x 30 internal thread.

A: Given:- M18 x 2.75 x 30   To find:- Depth of cut Root diameter

Q: er than 5mm annot be used when position ta han 0.1mm annot be used when position ta er than 4mm

A: Given Data : Counter sink fasteners

Q: A double-threaded power screw with square threads pushes against a load of 3,641 N at a speed of 15…

A: Here,  is lead angle,  is pitch,  is mean thread diameter.

Q: If a spline is transmitting 2,000 lb-in torque, what would be the major spline diameter for a 4A…

A:

Q: where does the 64 come from?

A: Given:Required:Explanation for 64 value in the moment of inertia equation.

Q: Would the plank and the roller have the same acceleration why or why not?

A: Given: There is no slip between any contact surfaces so the point of contact between the plank and…

Q: 2. UNC thread diameter D=3/4 in. Number of threads/in N= 10 Calculate: a. Pitch, b. Width of the…

A:

Q: Compute the lead angle of an M16 × 1 double thread.

A:

Q: General drafting practices do not recommend mixing partial views with auxiliary views. O True O…

A: Answer:  True

Q: I want to know how to count the full joint and the link on this drawing onlyy please put the number…

A: The diagram given in the question shows an Eight bar linkage, In kinematics, an eight-bar linkage is…

Q: A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire…

A: Given:Pitch, P=2 mmThread angle, 2θ=60oθ=30o

Q: 21 The root of a thread is defined as what? Multiple Choice (select the best answer) The surface of…

A:

Q: Q12) Determine the effective diameter of a metric screw using the three-wire method. The following…

A: Screw Screw is a thin pointed piece of metal used for fixing or joining two things like two piece of…

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.