What is the maximum value of shear at B? What is the degree of curve at shear BC? What is the moment value at point B in kN-m? What is the distance from the left support to the point of zero shear in m? What is the degree of curve at moment AB? What is the maximum value of shear in kN? What is the maximum value of moment in kN-m?

Q: From the given beam shown, and at the given point C, determine the following: a. the internal normal…

A: Consider the section ACB,

Q: Problem 3.7 - Forces P1, P2, P3, each of magnitude P, act on the edges of a cube of side "a".…

A: A diagonal is a line that connects one corner with the corner farthest away. It has slanted lines.…

Q: 8. The jib crane is supported by a pin at C and rod AB. If the load has a mass of 19,620N with its…

A:

Q: What is the horizontal reaction at C? What is the moment at point A?

A:

Q: Cable AC exerts on beam AB a force P directed along line AC. Knowing that P must have a 350-lb…

A:

Q: Problem 1 The bar supported by a pin at A and a cable at B carries a load of 260 N at C. Neglecting…

A: cable always carry tension so we make the free body diagram for analysis of the given beam. normal…

Q: The resultant of the three cable tensions acting on the flagpole is the force R acting vertically at…

A: Given- T3=500N The FBD is given below-

Q: Given beam (P = 24 kN) a) Find the internal forces at the midpoint of the BC length by cutting…

A:

Q: Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of…

A: Solution:Given Data:The concentrated load acting on the beam is P=5kipThe intensity of uniformly…

Q: in Figure A truss is supported by a pin at A and a cable attached at Q2(b). Determine the reactions…

A: To find the support reaction at A and force ni cable -

Q: Can you explain in detal why the moment about x is -0.450(150)? from my point of view it should be…

A: See the explanation given below. Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Problem 3: Support A is pin connected while support B is roller. Determine the resultant reactions…

A:

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A:

Q: The spool of wire having a weight of 300 lb rests on the ground at B and against the wall at A.…

A: Draw the free body diagram.

Q: A telephone cable is clamped at A to the pole AB. Knowing that th tension in the right-hand portion…

A:

Q: 10 EN 20 &N 743m Which of the following most nearly gives the reaction (KN) at the roller support?…

A: As per guidelines we need to answer only 1st three subparts of question

Q: drs - The semicircular rod has a 200 N load acting on it at the lower end in the direction shown in…

A: Given Data: The load acting on the lower end of the rod is P=200 N. The radius of the semicircular…

Q: 4. The block weighs 3500 kg. Find force in members AB, AC and AD. 1-5m 4m am

A: Given information: Mass of the block = 3500 Kg Weight of the block = m g…

Q: 3. If the plate is to remain in equilibrium, find the tension for all the three cable that supports…

A: Consider the following free body diagram:

Q: A pin-jointed plane truss which is supported by a pin at D and rest of rollers at A, and is…

A:

Q: To points A, B, C, and D respectively on an infinite-length plate Parallel forces FA, FB, FC and FD…

A:

Q: In a certain non-concurrent force system, it is found that E F= 90N, E F,= -120N and M,= 480N-m in a…

A:

Q: A shear force of V = 300 kN is applied to the box girder. Determine the shear flow at points A, B, C…

A:

Q: 50 KN 2m R,= WK/ (2m) R, 2w 30KN /m 5m werln. 2. Rz

A: Introduction : The force transverse to the beam at a given portion that tends to cause it to shear…

Q: A shear force of V = 450 kN is applied to the box girder. Determine the shear flow at points C and…

A:

Q: 400 N 2 m 2 m 300 N 2 m 1 m с Find the support reaction forces on the ball-and-socket joint at A,…

A: A plate is loaded with a roller at B and a ball-and-socket joint at A and a cable at CD.Roller at B…

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A:

Q: What are the reactions at support A and C? Moment of point B? Shear at point B?

A: Shear force is the sum of all the forces on either left or right side of the section of the beam.…

Q: 1. Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End…

A:

Q: EN h1 Prob. 12.23 Find the center of shear of the sections given in the figure.

A: Shear Force of Section : The shear force at any section is calculated as algebraic sum of forces…

Q: Determine the vertical reaction at support D in KN. Determine the maximum shear force in KN.…

A: Given data  Find support reaction, maximum shear force and maximum positive and negative moment.…

Q: 2. The Cable BC carries a tension force of 500 kN. Find the components of the tension force along BA…

A: The given figure is shown below:

Q: Determine the shear force and bending moment at section C. 200 N/m A₁ = 800 N -3 m- C 3 m 400 N/m B.…

A:

Q: Draw the shear and moment diagram of the structure shown below.

A: Draw the free-body diagram of the beam. Write the equilibrium equation for the sum of the moment…

Q: Analyze the given beam using consistent deformation method (force method), show complete solution.…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.