What is the main difference between the JMP instruction and the JSRR instruction? O There is no difference, JMP is a pseudo instruction for JSRR O The JMP does not back up the PC into R7 and the JSRR instruction does JSRR uses the PC to calculate the effective address, and JMP uses a base register O The JSRR does not back up the PC into R7 and the JMP instruction does JMP uses the PC to calculate the effective address, and JSRR uses a base register

What is the main difference between the JMP instruction and the JSRR instruction? O There is no difference, JMP is a pseudo instruction for JSRR O The JMP does not back up the PC into R7 and the JSRR instruction does JSRR uses the PC to calculate the effective address, and JMP uses a base register O The JSRR does not back up the PC into R7 and the JMP instruction does JMP uses the PC to calculate the effective address, and JSRR uses a base register

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

List general purpose registers and explain why they are called so. Distinguish the purposes of flag register from other registers. If AX= 1001H and DX=20FFH, list the sum and the contents of each flag register bit (C, A, S, Z, and O) after the ADD AX, DX instruction executes.
Microprocessor Hw Q1 Execute the following code and show the contents of the registers: LDI R16,$03 LDI R17,$10 HERE: AND R16, R17 BREQ HERE ADD R16,17 Q2 Find the number of times the following loop is performed: LDI R20,20 BACK: LDI R21,$0A HERE: DEC R21 BRNE HERE DEC R20 BRNE BACK Q3. Execute the following code and show the contents of the registers: LDI R16,$03 LDI R17,$15 HERE: ADD R16, R17 COM R16 BRSH HERE EOR R16,17 JMP NEXT SUB R16,R17 NEXT: ROR R16
Consider a 16-bit processor in which the following appears in main memory, starting at location 200: B. The first part of the first word indicates that this instruction loads a value into an accumulator. The mode field specifies an addressing mode and if appropriate, indicates a source register; Assume that when used, the source register is R1, which has a value of 400. There is also an index register (XR) that contains 100. The value of 500 in location 201 may be part of the address calculation. Assume that location 399 contains the value 999, location 400 contains the value 1000, and so on. Determine the effective address and the operand to be loaded for the following address modes:
What is the effective address that is targeted by the store instruction whose code word in binary is:101011 01000 10001 1111 1111 1111 1100Assume [$t0]=0x400C
Suppose the opcode of an MIPS instruction is 8 in decimal, and the rest of the machine code is 309FC88 in hexadecimal (from high-order bit to low-order bit). What is the instruction? When showing the registers, use names (e.g. $t0, $s2) instead of indices (e.g $8, $17). For branch instructions, show offset in place of label, e.g. beq $t1, $t2, 92. Answer:
If short JMP instruction reside in memory location 02001 what is the ?address of next instruction 02002 O 02003 O 02001 O none of them O
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and j are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and x11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 1w x30, 0 (x3) 1w x31, 0 (x4) add x30, x30, x31 sw x30, 16 (x11)
An instruction is stored at location 100 with its address field at location 101.The address field has value 200. A processor register R1 contains the number 300. Evaluate the effective address if the addressing mode of the instruction is A. Direct B. Immediate C. Relative D. Register Indirect E. Index with R1 as the index Register
Assume that the instruction pointer, EIP, contains 9810 and the assembly language representation of the instruction in memory at address 9810 is JAE 131. If the flags are currently CF=1, ZF=0 and SF=0 what is the value of the EIP after the instruction executes? The answer 102 is not correct so what is the correct answer?
Q1: Suppose the initial stack pointer of the interrupt stack is 0x81009A90, what is the value of SP after the interrupt handler has pushed the general purpose registers onto the interrupt stack? Q2: What is the value of the PC right before the general purpose registers have been pushed? Q3: After the RFI instruction has completed, what is the value of the PC? Q4: After the RFI instruction has completed, what is the value of the SP?
Suppose the opcode of an MIPS instruction is 9 in decimal, and the rest of the machine code is 1F67875 in hexadecimal (from high-order bit to low-order bit). What is the instruction? When showing the registers, use names (e.g. $t0, $s2) instead of indices (e.g $8, $17). For branch instructions, show offset in place of label, e.g. beq $t1, $t2, 92.
MANUALLY decode the following ARM machine language code to ARM assembly instruction. 0x34532911 Write your answer in TWO parts, the Op-Code in a box and ALL operands in another box. The Op-Code of the instruction is: The operands of the instruction are: