What is the gauge pressure at Point G in the figure below (Patm=101.3kPa).Open toatmosphereClosed top1mPlan view (view E-E)Open to atmosphere1'Om1.0m Air1.5mAir2.0 ms=2 2.0 mWaterGElevation viewO a.169.97 kPaO b. 88.29kPa189.59 kPaO d. None of the mentionedO e.68.67 kPa

Answered: Image /qna-images/answer/38d864db-7e10-40b1-a3f5-f288cb886339.jpg

What is the gauge pressure at Point G in the figure below (Patm=101.3kPa). Open to atmosphere Closed top 1 m Plan view (view E-E) Open to atmosphere 1'0m F2 m- 1.0m Air 1.5m Air 2.0 m S=2 2.0 m Water G Elevation view

What is the gauge pressure at Point G in the figure below (Patm=101.3kPa). Open to atmosphere Closed top 1 m Plan view (view E-E) Open to atmosphere 1'0m F2 m- 1.0m Air 1.5m Air 2.0 m S=2 2.0 m Water G Elevation view

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 350 mm x 500 mm rectangular beam carries a uniform dead load of 4.5 kN/m (including its own weight) and uniform live load of 3 kN/m. If a concentrated live load P 150 kN was added as shown in the figure, a) calculate the tension steel area required to support the loading. b) determine how many 20 mm diameter rebar was needed. c) draw the cross-section of the reinforced rectangular beam.
8 m A 2 kN/m D6m 4 m B 15 kN 5m Figure no. 1 6 m C
Problem #2 50 kN 15 kN/m 90 kN EI constant %3D D E=70 GPa C I=95x10 mm Required: 8A 8c 0B 6 m 9 m- -9 m
Assigned P values 167.5
Fluid mechanics, i need solutions in 10 minutes please. MCQ/Curved panel BC shown in the figure is a 60 ° arc, perpendicular to the bottom at C. If the panel is 5 m wide into the paper, compute the vertical component of the hydrostatic force of the water on the panel. A-267.865 kN B-284.257 KN C- 218.953 KN D- 156.568 KN E- 141.993 KN F-235.066 KN G- 251.017 KN H-114.631 KN I-128.004 KN J-319.178 KN K-186.655 KN L-300.428 KN M-202.738 KN N-171.524 KN
ILLUSTRATE THE GIVEN PROFILE LEVELING NOTES BELOW. THE SECOND PICTURE IS THE REFERENCE FOR THE DRAWING. PLEASE DO NOT GIVE A SOLUTION OR RECHECK THE WORK. I AM ALREADY DONE WITH IT. JUST PROVIDE THE ILLUSTRATION USING THE REFERENCE.
Situation 1 Determine EI8 at point Band end of the overhang. Round off your final answer in2 decimal places. W1 W2 A LB X1 X2 X3 Given: X1 7m X2 6m X3 5m W1 34kN/m W2 30kN/m a.) Είδ b.) EIS at the end of the overhang
Fluid mechanics, i need solutions in 10 minutes please. MCQ/The submerged sector gate AB shown in the figure is 1/9 of a circle radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. A-262.874 kN B-162.328 KN C-324.260 KN D- 448.161 KN E- 591.263 KN F-392.273 kN G- 89.207 kN H-536.078 KN I-208.119 KN J- 490.984 kN K- 127.908 KN L- 113.001 KN
REFER TO FIGURE 01, DETERMINE THE INTERNAL FORCES ACTING ON THE FOLLOWING MEMBERS: (STATE COMPRESSION OR TENSION) FG FC GH CH
2. (a). Obtain the total elongation of a steel bar of cross-sectional Area 1250mm2 acted upon by forces indicated in the diagram below. E-205,000N/mm2 15N- 5N 20N 40N 15N 1.5m 1.5m 3m Im TAt man Im 12. 5omx
N1
ELEVATION 20M ELEVATION 30m AIR Po? 150mmø SG-0.84 Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2 is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84) (А) 82.19 КРа в) 87.74 КРа с) 98.23 КРа D) 93.30 КРа E) 76.49 KPa