What is the formability?

Q: Compare Boiling Point with Vapor Pressure?

A: The boiling point has to be compared with with Vapor Pressure

Q: If each edge is 1 cm. How much liquid does this shape hold

A: Answer  Calculate the total Volume   By  using the square and…

Q: Define Boiling point?

A: There are mainly three states of matter known as solid, liquid, and gases. The conversion of a solid…

Q: Does solid state stearic acid has a viscosity at room temperature

A: Viscosity is a measure of a fluids resistance to flow. It is a frictional forces resulting due to…

Q: 3. True or false: Because dry ice sublimes, carbon dioxide has no liquid phase. (a) True (b) False

A: The statement is True

Q: 4. What do you mean by eutectic point? Discuss eutectic point with help of suitable diagram? Discuss…

A:

Q: 1. Draw the phase Diagram of a one component system which contain more than one solid phase and…

A: the answer is as follows:

Q: Discuss briefly factors that influencing plastic properties.

A: Plastics are semisynthetic materials with polymer as an active ingredient. Thus the properties of…

Q: What is the force of attraction between liquid molecules?    a) Viscosity  B) adhesion  NS)…

A: What is the force of attraction between liquid molecules?

Q: Define Solid aerosol, solid foam and solid sol

A: Solid aerosols, solid foam, and solid sol are all heterogeneous solutions and classified as…

Q: What would be the possible application of determining the melting point of a substance?

A: Below attached file showing the details answer.  All the best.

Q: Can you explain the Physical vapor deposition process in simple term

A: Introduction :  The process by which a substance changes from the gaseous state to the liquid state…

Q: Define oil viscosity.

A: Viscosity is a physical property of liquid that depends on various factors like intermolecular force…

Q: How much heat is required to heat 59.3g of liquid ethanol from -7*C to the vapor state at 78*C

A: Given,  Mass of liquid ethanol = 59.3 g.  Initial temperature = - 7 °C Final temperature = 78 ° C…

Q: How can we describe a single-phase material?

A: Single phase material is the material contains only one phase .

Q: Which of the following compounds can form STRONG hydrogen bonding with itself? elect one: III and IV…

A: Answer  Hydrogen bonding :- hydrogen bond attach with more…

Q: 8)Why measuring melting points?

A: You have a good question

Q: Describe the properties of a liquid, including vapor pressure, viscosity, and surface tension

A: To find: The description about the properties of a liquid including viscosity, vapor pressure and…

Q: .Why is slow cooling required to produce pure crystals?

A: We are to discuss why slow cooling is done to form pure crystals.

Q: As a liquid sample is heated without a phase change, which physical property will decrease?  a)…

A: We know, volume increases with increasing of temperature due to increase in kinetic energy.  And we…

Q: Discuss the cohesion and adhesion properties of water, with two examples for each.

A: Water has 2 type of properties of attraction, cohesion and adhesion. Cohesion is the attraction…

Q: A rectangular solid was found to have measurements of 4.78 cm by 6.97 cm by 0.90 cm. The mass of the…

A:

Q: What is a single molecule called?

A: A single molecule experiment is an experiment that investigates the properties of individual…

Q: what is denser water or chloroform? why? elaborate

A: Chloroform (CHCl3) is a nonpolar liquid. On the other hand (H2O) is a polar liquid. The molar mass…

Q: Think about the structures of the molecules. a) CH3COCH2 CH₂ (butanone) b) C(CH3)4 AHvap. In each…

A: Boiling point is the temperature required to transform liquid to gas . Where vapor pressure is the…

Q: List porosity of sand, silt, loam, and clay in order.

A: Porosity is the measure of void space in a material and is the fraction of volume of voids over the…

Q: The properties of primary substance must be pure O known chemical structure

A: A multiple choice question based on analytical chemistry, which is to be accomplished.

Q: 3. What do you mean by vapour pressure ? Explain the vapour pressure curves in water and sulphur…

A: Answer - Vapour pressure - Vapor pressure is defined as the pressure exerted by a vapor in…

Q: H2(g) + CO2(g) H₂O(g) + CO(g) Solution First we will set up an equilibrium table. It is important to…

A:

Q: A solid will melt to its liquid phase if enough heat is applied. O True 3 False

A: Solution- when enough heat is applied to solid it will change to liquid phase which is known as…

Q: The enthalpy of vaporization of Substance X is 25.0 Round your answer to 2 significant digits. atm 0…

A:

Q: Why would the cohesion and thermal stability of water beless if water did not have polar covalent…

A: Water is an inorganic, unscented, and most dismal synthetic substance, which is the principle…

Q: List two examples of liquid

A: Liquid is a physical state of matter which do not have fixed shape but have definite volume. A…

Q: Explain the reason behind why oils leave a translucent spot on paper even after drying, while…

A:

Q: an electrical current can produce which type of force?

A: Electric current is produced By flow of electrons or charges , When a charge flow magnetic field is…

Q: 2. With the help of the Phase rule, draw and describe the phase diagram of Sulphur system.

A:

Q: Paper Clip 1 Paper Clip 2 m Before Paper Clip 1 8P Paper Clip 2 Paper Clip 1 Paper Clip 2 mpy Magnet…

A: B. Magnetism travelled through paper clip 1 to paper clip 2 and made them magnetic.

Q: Rank cork, concrete, copper and glass from most heat conductive to least.

A: HEAT CONDUCTION:- Heat conduction is transfer of heat from higher temperatures to low temperature.…

Q: A solution is made by dissolving 27.5 g of HONH3CIO3 in 500.0 mL of water. Using Ka(HONH3*) = 9.1 ×…

A: The amount of HONH3ClO3 dissolved in 500.0 mL of water is 27.5 g. The dissociation constant of…

Q: can you write and intro and explain about LNG liquefaction process and cooling of natural gas

A: Natural gas is converted to a liquid in a liquefaction plant,or “train”. An LNG train performs three…

Polymerization Kinetics

Polymerization is a chemical process in which one or more monomers combine to produce a very large chain-like molecule called a polymer. The functional groups present on the monomers and their steric effects are responsible for polymerization through a sequence of reactions that diverge in complexity. There exists a stable covalent chemical bond between monomers that sets apart polymerization from other processes. Polymerization is generally classified into step-growth and chain polymerization. Polymers are categorized into linear polymer and cross-linked polymers that are produced either by condensation or additional polymerization.