What is the flow rate of the oil (sg = 0.73) in the pipe below based on the measurements in the venturi meter? The Resistance Coefficient of the valve is 0.5. DN65 Schedule 40 pipe 0.19 m Flow Mercury (sg = 13.54) 23 mm

Q: How can you determine the velocity of the flow in the channel with the venturimeter in the pire…

A:

Q: The 200 mm diameter galvanized iron pipe transports water from a reservoir at a temperature of 20oC.…

A:

Q: What is the pressure drop in psi of 60°F water flowing through 65 ft of horizontal 1-inch schedule…

A: Consider the solution below

Q: Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a…

A:

Q: The hydraulic radius of a pipe with diameter of 12 mm is equal to 3 mm 6 mm 9 mm 4 mm

A: hydraulic radius is the ratio of wetted area (A) to the wetted perimeter (P). i.e. Rh=AP For…

Q: Calculate the Reynolds number of the flow of water flowing with the velocity of 1.5 m/s and the…

A:

Q: Crude oil having a specific gravity of 0.93 and a viscosity of 4cP is draining by gravity from the…

A: Given,   Specific Gravity = 0.93 Coefficient of viscosing is = 4cp = 4 x 10-2  poise  = 4 x 10-3 pas…

Q: hich of the following is turbulent flow according to Reynolds number for pipe?   a.   Re is less…

A:

Q: The head loss through fluid flowing pipe due to friction is minor loss in the pipe Select one: O…

A: The head loss through fluid flowing pipe due to friction is major loss in the pipe Minor loss are-…

Q: The pitot tube is used to measure the ratre of flow at the required point in a pipe Select one: True…

A: Pitot tube also called as pitot probe is a flow measurement device which is used to measure the…

Q: 1. What is the likelihood that a flow with an average velocity of 0.15 f t/s in a 6 in. water pipe…

A: Since you have posted multiple independent questions we will solve the first question for you To get…

Q: A 400 gpm piping system is composed of the following pipes and fittings. Using the chart;…

A: The model framework is a water supply framework in a modern plant. The framework incorporates a…

Q: A venturi meter convergent part is smaller than a divergent part. Select one: True False

A: It is True.

Q: 1. Determine the pump work of the oil piping system. The oil has kinematic viscosity of 0.0001 m²/s…

A:

Q: 1-Comment on the differences in reading measurements and whether these differences could be from…

A: Answer:1)i)The accuracy of measurements of readings in flows depends on the fluid properties.ii)The…

Q: Determine the friction factor “f “ for a 40 mm ID cast iron pipe handling 400 L/min of water using…

A: Given:  D = 40 mm  For cast iron pipe, equivalent surface roughness (∈)=0.26 mm  Q = 400 L/min = 0.4…

Q: What is the differential reading on a pitot tube inserted at the centerline of an 8-inch ID pipe…

A: The data given is, Discharge, Q = 1200 gpm The diameter of the pipe, d = 8 in. = 0.667 feet Ratio…

Q: The ratio of entry diameter with exit diameter is 0.4 in a control volume of pipe segment. What is…

A:

Q: l between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number.…

A:

Q: 1. Which of the following is used to increase flow velocity from a pipe? Group of answer choices…

A: Nozzle A nozzle is a device or a pipe used to modify the flow. As seen from the figure the nozzle…

Q: What must the gauge pressure p be at A if the volume flow rate out of the pipe at point B is 0.0800…

A:

Q: 4. If the pressure difference between points 1 and 2 below is 90 psi, what will be the flow rate?…

A:

Q: List two sources of error in the water-filled tube and pressure gauge method of measuring head for a…

A: Solution:   (1) Two sources of error in the water-filled tube and the pressure gauge are:

Q: The coefficient of friction for a flow through pipe with Reynold’s number 40000 is a. Need density,…

A:

Q: How can you determine the flew rate in the channel with the venturimeter in the Rire siccuit in the…

A:

Q: Q1:-Answer the following statements with (True) or (False), (choose 5 only) 1-The Bernoulli's…

A:

Q: There is a PVC pipe, with an internal diameter of 28 mm. The Reynolds number for this system is…

A: here  D= 28 mm Re=1500  ε=0.0015 swami jain method ... f=0.25[log(ε/D3.7+5.74Re0.9)]2

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.