ToplambasınçgöstergesiManometreVanaVenturimetreDebiölçerHaznePompaManometre=ManometerVentwrimetre=VentwrimeterDebiölcer-Flow meterVana=ValvePompa=PumpHazne=TankToplam Basınç Göstergesi =Total Pressure GaugeHow can you determine the velocity of the flow in the channel with the venturimeter in thepipe circuit in the figure?

Answered: Image /qna-images/answer/0afee1a8-6a2f-4f5b-9cb4-612b8b1e23c3.jpg

Answered: How can you determine the velocity of…

Engineering

Mechanical Engineering

How can you determine the velocity of the flow in the channel with the venturimeter in the pire citcuit in the figure?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30 m and has an efficiency of 70%. If this pump is situated 9 m below the level of the source, calculate (Zs)max and determine if the pump is safe from cavitation. Select one: O a. -7.9 m; NOT SAFE O b. -9.7 m; NOT SAFE O c. -7.9 m; SAFE O d. -9.7 m; SAFE
35 + 9.81 (0.3824 - 7-2) = - 49.54 kPa. S. Chand Je oadall i.e.p =- 49.54 kPa. This shows that the given pressure at A, 35 kPa is gauge pressure and hence there is vacuum at point B. (Ans.) Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P.- 100 kPa water is 999 kg/m' and characteristic gas constant for V =0 air is 287 J/kg K. ساP حقوق النشر Test section 25°C. = 25°C (GATE)
Please help me with this problem clearly. List two sources of error in the water-filled tube and pressure gauge method of measuring head for a hydro system and how to avoid them. Using this method, a series of measurements up a hill to the source of the stream produces the following heights: 1.5m, 0.7m, 1.0m, 1.9m, 1.6m, 0.3m, and 0.8m. What is the total head for this site? If the flow rate was 0.5 m3s-1, calculate the power available in this stream?
A pipe with a diameter of 2cm is attached to a garden hose with a nozzle. If the velocity of flow in the pipe is 2ms, what is the velocity of the flow at the nozzle when it is adjusted to have a diameter of 4mm?
A circular pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/s, then the average velocity through the bifurcated pipe is
Describe and Draw Energy Grade Line (EGL) &Hydraulic Grade Line (HGL) Describe and write the formulas measuring flow rate in pipes using Orifice.
Toplam basınç göstergesi Manometre Vana Venturimetre Debiölçer Hazne Pompa Manometre=Manometer Ventwrimetre=Ventwrimeter Debiölçer-Flow meter Vana=Valve. Pompa=Pump Hazne=Tank Toplam Basınç Göstergesi =Total Pressure Gauge How can you determine the flow rate in the channel with the venturimeter in the pipe circuit in the figure?
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. Choices are listed below and draw its FBD. A.-4.67 m B.-2.72 m C.12.74 m D.2.56
Q2' A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of flow in the pipe is 4 m/s, what is the velocity of the flow at the nozle when it is adjusted to have a diameter of 16 millimeters, and what is the flow rate?
Drive the formula for Pipe flow system.
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200- 150 - 6 125- Suction lines 100 - 4 3. 65 2 50E 2 Discharge lines 40 - 32 - 25 E 15 15 20 30 40 60 200 400 600 S00 2000 4000 6000 S00 80 100 10 Volume Flow Rate, Qallmin) 8 10 15 20 25 30 40 +++++ +++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 +++++ +++++ Volame Flow Rate, Q (mVh)
A pitot tube directed into a water stream having a velocity of 2.7 m/sec. It has gauge difference of 30 mm on the water mercury manometer. Find its coefficient.