Answered: What is the Estimated Ultimate Recovery…

Name: The following data are for a neighboring well with an ongoing product
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The following data are for a neighboring well with an ongoing production decline:• qoi= 948 STB/day.• D₁=0.09/yr• b=0.5What is the Estimated Ultimate Recovery for this reservoir?The units for your answer should be MMSTB and your answer should be pre

Engineering

Mechanical Engineering

What is the Estimated Ultimate Recovery for this reservoir?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hair dryer is basically a duct of constant diameter in which a few layers of electric resistors are placed. A small fan pulls the air in and forces it through the resistors where it is heated. If the density of air is 1.20 kg/m³ at the inlet and 0.895 kg/m³ at the exit, determine the percent increase in the velocity of air as it flows through the dryer. P kg/m³ 1.20 kg/m³ The percent increase in the velocity of air is 42 %.
A garden hose attached with a nozzle is used to fill a 40-literbucket. The inner diameter of the hose is 2.0 cm, and it reduces to1.0 cm at the nozzle exit. If it takes 59N s to fill the bucket withwater, determine (a) the volume and mass flow rate of waterthrough the hose, and (b) the mean velocity of water at the nozzleentry and exit
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is open to the atmosphere and the water enters the tank from a 80-m-height. The overall efficiency of the motor-pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 kW. Take the correction factor to be 1. If the irreversible head loss in the piping is 7 m, the velocity of the water at the tank inlet is (a) 2.34 m/s (b) 4.05 m/s (c) 6.21 m/s (d ) 8.33 m/s (e) 10.7 m/s
A vessel contains water. The conditions of the system are: volume of the vessel: V = 0.10 m3 presure of water: P = 200.00 kPa mass of water: m = 5.00 kg specific volume of the saturated water at the pressure: vf = 0.001061 m3/kg specific volume of the saturated vapor at the pressure: vg = 0.885780 m3/kg enthalpy of the saturated water at the pressure: hf = 504.71 kJ/kg enthalpy of the saturated water at the pressure: hg = 2706.30 kJ/k difference of enthalpy of the saturated vapor and saturated liquid at the pressure: hfg = 2201.60 kJ/kg Determine (1) the specific volume of water in the vessel, v=_____m3/kg
We use a 5 meter long cable with linear mass density of 9 kg/m to lift a bucket of water with total mass of 15 kg (that is the mass of the bucket and the water). The bucket is leaking water out of a small hole in the bottom at a rate of 3 kg per meter lifted. Find the total amount of work done to lift the bucket 4 meters. Do not include any units in your answer.
A large reservoir (volume = 75x109 m³) has been designed with 25 percent of its volume for sediment storage. If the influent streams have a total flow rate of 50x106 m³/d and an average suspended solids concentration of 300 g/m³, determine the expected life of the reservoir. Assume an average sediment density of 1600 kg/m³.
A vessel contains 10 kg of water at 10 kPa and 1kPa.Determine specific and total internal energy, specific and total enthalpy, and specific and totalentropy. Cosider different cases/states:I. T = Tsat and x = 0II. T = Tsat and x = 0.5III. T = Tsat and x = 1IV. T = 300 ⁰CPlot these states on the T
An electric motor with an efficiency of 80% drives the pulley system shown to lift a 400 kg crate. After the motor is turned on the system reaches a constant lifting speed vo and the motor is drawing 15 kW. Assume that the motor is operating at it rated efficiency and the friction losses and mass of the pulleys are neglgibile. Determine v0. 19 m UO
The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is 95 percent. The water flow rate through the pump is 50 L/s. The diameters of the inlet and outlet pipes are the same, and the elevation difference across the pump is negligible. If the pressures at the inlet and outlet of the pump are measured to be 100 kPa and 300 kPa (absolute), respectively, determine the mechanical efficiency of the pump. Water 300 kPa 100 kPa 150 Ls motor Motor 15 kW The mechanical efficiency of the pump is %.
Which one is not an assumption involved with the Bernoulli equation? (a) No elevation change (b) Incompressible flow (c) Steady flow (d) No shaft work (e) No friction
R-134a enters a compressor as a saturated vapor at 80 kPa and exits at a pressure of 400 kPa. If 44 kJ/kg of work is required and 5 kJ/kg of heat is lost to the surroundings. What is the outlet temperature. Round your answer to the nearest whole number.
An iron bar 2.0 cm x 3.0 cm x 10.0 cm at a temperature of 95 °C is dropped into a barrel of water at 25 °C. The barrel is large enough so that the water temperature rises negligibly as the bar cools. The rate at which heat is transferred from the bar to the water is given by the expression Q (J/min) = UA (T₁-T) where U = 0.05 J/(min cm °C)] is a (cm) is the exposed surface area of the bar, T, and T are the surface temperature of the bar and the water temperature, respectively. The heat capacity of the bar is 0.46 J/g °C). Heat conduction in iron is rapid enough for the temperature T, to be considered uniform throughout the bar. a) Write an energy balance on the bar b) Plot the expected plot of T, versus t and then curve fitting. M = (60 cm³) (7.7 g/cm³) = 462 g C, = 0.46 kJ/(kg-°C), T = 25°C U= 0.050 J/(min-cm².°C) 4 = 2[(2)(3)+(2)(10)+(3)(10)]cm² = 112 cm²