Answered: What is the concept of ALARP? Give an…

Engineering

Mechanical Engineering

What is the concept of ALARP? Give an example of a situation where the ALARP principle is applied. (1 page max.)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Related questions

Q: The figure shows a cross section of a conventional loudspeaker. A voice coil (driven by the audio…

A: Given Data The magnetic field intensity is:H=4×104 A/m The length of the permanent magnet is:lm=25…

Q: Nanotechnology, the field of building ultrasmall structures one atom at a time, has progressed in…

A: Write the given data:

Q: Please show all work!

A: In the problem statement:Given:A stress matrix (ksi) σ:To be found:Calculate the principal…

Q: Find the axial stress (Subscript[\[Sigma], z]) and axial strain (Subscript[\[Epsilon], z]) for a…

A: Axial Stress (σz): Under plane strain condition, the axial stress is often assumed to be uniform…

Q: Show material below deforms when temperature difference across exceeds the threshold of ZTC if the…

A: The threshold temperature difference, The thickness of the material,

Q: There is a useful relationship between permutation symbol and Kronecker delta, given in Eq. (2).…

A: The relationship between the permutation symbol ε (ijk) and the Kronecker delta δ (ij) is given by:ε…

Q: Q31 Eddy diffusion calculation A stream of air at 100 kPa and 300 K is flowing on the top surface of…

A: The objective is to determine:1) the mass transfer coefficient over the flat plate.2) The rate of…

Q: Q8 (a). Find all the stable structure(s) as shown in Figure 8a. wwwwww (a) www (b)

A: in the above 4 figure only Figures (a) and (c) are stable figures as they do not have moving joints.…

Question

What is the concept of ALARP? Give an example of a situation where the ALARP principle is applied. (1
page max.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. Kittel Ch3-4. Energy fluctuations. Consider a system of fixed volume in thermal contact with a reservoir. Show that the mean square fluctuation in the energy of the system is ((x − (e))²) = t² (əU / ət), Here U is the conventional symbol for (e). Hint: Use the partition function Z to relate U/ar to the mean square fluctuation. Also, multiply out the term (...). (89)
Please explain the formula for the derivation of isothermal because I can't derive the formula, or provide similar references
(Solid Mechanics) This plate is clamped into a wall is subjected to a force F as shown. The wall does not generate any stress concentration. At the fillets the stress concentration factor is given Kt = 1.5 (No need of using charts). The plate is made of a cast iron with the following properties:Modulus E=150 GPaTensile strength Sut =200 MPaCompressive strength Suc=600 MPaWhere and how could the plate fail and at which force Fmax?
Q. 3-20
Please solve the problem correctly,Thanks. Don't use ai
Using gas state equation, calculate density of air and pressure
The largest animal is found in sea as it requires no energy to support its weight by using hydrostatic principle. However bird has to support its own weight by using Bernoulli principle to create pressure difference while in flight. Bird cannot be very large and there are also fewer species of large bird than small bird. The reasons are: (i) (ii) There is less food in the air than in the sea. The bone structure of the bird has to be light and it is structurally more difficult to maintain the strength to weight ratio as the bird becomes larger. The lift and drag on a bird is due to viscous and pressure forces. They are surface forces proportional to the length square while the weight of a bird due to gravity is proportional to the length cube. At large length scale, length square is much smaller than length cube and it becomes difficult to generate lift to support a bird in flight. (A) (B) (C) (i) and (ii) (i) and (iii) (ii) and (iii) All of the above
Pipe Pa Fluid Rigid rock Figure 1: A pipe embedded in rigid rock. Consider an isotropic linear elastic pipe of inner radius a and outer radius b embedded in rigid (i.e., non-deforming) material and holding a fluid at pressure Pa. Ignore the effects of gravity. This may be a good model for a PVC pipe embedded in rock or concrete. Assume the problem is symmetric and that strains out of the plane shown in Fig. 1are zero. (a) What state of strain exists in the pipe, plane strain or plane stress? (b) Determine the stress components, orr and σ00, and displacements, ur, in the pipe. (c) Is the stress difference orr - 000| greatest at r=a or r = b? Note: the location of the greatest stress difference is where plasticity will occur first (to be covered later in class).
What is the Temperature of 02 gas if it starts at 45oC and a volume of 7L and ends at a volume of 30L? (1372 K)
Problem 3: Hydrostatics The cubical block depicted in the figure below is shifting between two fluids of the same volume Vo = 6m³, in a tank with length L = 12m and width w = 2m. The side length of the block is R = 2 m. PzP1/2 R P1 L + Figure 3: Equilibrium position due to two liquids of different densities. 1. Find the equilibrium positions of the shifting block. 2. Will the block pivot for p₁ = 1000 kg/m³ and SG block = 2.4?
A metal piston is placed in the top of a cylinder containing a gas and a liquid, as shown in the figure below, compressing the gas. Assume that the interface between the piston-cylinder is frictionless and forms a perfect seal so that none of the gas can escape. (a) Derive the equation for the absolute pressure of the gas. Identify each variable and use the subscripts P, G, and L to variables specific the cylinder, gas or liquid. State any and all assumptions. (b) Calculate the absolute pressure of the gas (in kPa) for the case where the disc is made of copper, the gas is air, the liquid is water, the diameter of the cylinder is 10cm and the height of the piston is 3cm. Values for needed constants can be found in Chapter 1 of your text, along with Tables A-1 and A-3. piston gas liquid piston gas liquid
I'm wondering how z2 was derived. I've highlited where I am getting confused. Shouldn't the derivative of z2 should only be equal to x2; where, z2 = 0.5x^2/2. I don't understand how z2 = x2 multiplied by the derivative of x2.