Please show all work!

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: The following is a schematic diagram of the Charpy impact tester. Is from the following. At this…

A:

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: can you make a sketch of the solution

A:

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: Files are used for removing large of amount of materials. Select one: True False

A:

Q: Please send Complete answer for getting upvote  Detailed answer  what is Flyweight Design Pattern…

A: given; what is Flyweight Design Pattern Application  Real world example

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: y

A:

Q: A solid cylinder is rolling down a ramp that is rough enough to cause the cylinder to roll without…

A: This question is solved with the help of the law of conservation of energy. Under pure rolling,  The…

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: Find the velocity of bullet fired in standard air if the Mach angle is 45°. Take R=287.14 J/kg K and…

A: Data given-  Mach angle = 45°  R = 287.14 J/kgK  k = 1.4  T = 27 + 273 = 300 K

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: Center of gravity of a plane area. Shear force. Point of contraflexure.

A: Centre of gravity of a plane area: The centre of gravity of a plane area is a point inside or…

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: What kind of information does a detail view on a drawing provide

A: A detailed drawing can be drawing of an object, assembly of multiple parts, or an entire system of…

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: can this be done using simpsons rule?

A: As already calculated using the relation    for the volume ranging from to  in steps of , the…

Q: What is the max circularity, on a radius, on the part below before a feature control frame is…

A: The tolerance of the part is

Q: Engineering Drawing: Dimensions

A:

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .