What is the balanced steel reinforcement (mm²) of the beam if it has a specified compressive strength of 27 MPa and steel yield strength of 299 MPa? The width of the beam is 420 mm and it has an effective depth of 732 mm. Round off only on your final answer. (3 decimal places)

What is the balanced steel reinforcement (mm²) of the beam if it has a specified compressive strength of 27 MPa and steel yield strength of 299 MPa? The width of the beam is 420 mm and it has an effective depth of 732 mm. Round off only on your final answer. (3 decimal places)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A cantilever beam, held by a fixed support on one end, is subjected by the forces shown in the…

A: Draw the free-body diagram of the given figure. Given that, FA=12100=0.12 NFB=0.06 Nβ=25°θ=19°L=5.2…

Q: A large tank open to the atmosphere is filled with water to a height of 9.3 m from the outlet tap. A…

A: Discharge through the mouth piece= Q=Cd a2gH Velocity = Q/a= Cd2gH= 0.7072*9.81*9.3= 9.55 m/s So the…

Q: FIGURE 1 50 kN C 100 kN 1.5 E 20 2.0 2.0

Q: For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x).…

Q: :A stone is projected vertically upward from the top of a 120m-high tower at a velocity of 36 m/s.…

Q: c. A weir in a horizontal channel is 12 ft wide and 4 ft high. The upstream water depth is 5.2 ft.…

A: Thank you for the question . As per honour code we will answer the first question since exact one…

Q: The T-beam has an effective flange width of 835 mm and the thickness is 112 mm. If the area of the…

A: The given data is shown below: Effective flange width=835 mmThickness=112mmArea of compression…

Q: For a fully developed laminar flow of water (dynamic viscosity 0.001 Pa-s) through a pipe of radius…

A: Given data- dynamic viscosity μ=0.001 Pa-sRadius R=5 cmpressure gradient ∂P∂x=-10 Pa/mradial…

Q: Water flows from reservoir A to a turbine and then discharges into tailrace B, as shown in the…

A: step 1-

Q: he figure. It is required to grade to a level surface of elevation 10m. Deter ill required by unit…

A: 1. Using the parallel section method, Area of each square 10x10 = 100 sqm Calculations of the…

Q: Determine the reactions of the given beam using slope deflection method. P₁ = 25 kN, P₂ = 25 kN, and…

A: Given:P₁ = 25 kN, P2 = 25 kN, and w = 35 kN/mRequired:Support reaction and moment at D

Q: A parabolic curve has a descending grade of -0.88% which meets an ascending grade of 0.45% at sta.…

Q: The motion of pin P is guided by slots cut in rods AD and BE. Knowing that bar AD has a constant…

Q: GIVEN: A bedroom & bathroom with floor area of 45sq.m., productivity of 1 tilesetter (5 sq.m/day)…

Q: A slow leak from an underground storage tank has contaminated both the soil and the groundwater as…

A: Given, Dimension of storage tank= 5x10x2 m Therefore, Volume =100m3 Density of soil, γ=1800kg/m3…

Q: Lil Sample Problem 2 2. Calculate the velocity of water flowing in point 2? Water Open Tank

A: The depth of water in tank, h=3mThe tank is opoen to atmosphere.

Q: A cantilever beam has a length of 3 m and 400 mm depth. Is the beam depth permissible by the code?…

A: Given , length of beam =3m=3000mm Depth=400mm Ratio of length to depth =3000/400 =7.5:1 But code…

Q: A light-weight concrete was cast-in-place to form a rectangular beam. If its unit weight is 16.362…

Q: For the beam shown, derive the expressions for V and M, and draw the shearforce and bending moment…

Q: A cantilever beam is subjected to load Pat mid-span and counterclockwise moment M at B (see figure).…

A: The figure is as shown.Standard Formulae will be used

Q: description [1] L4x4x3/8 angle in tension along its length (steel) length ft 18 L4x 4x3/8 = 2.4 in…

A: L4 x 4 x 3/8 section Area, A = 2.9 in2Load, P = 46 kips

Q: Determine the frictional force created between the 490.50N wOoden box and the ground if P = 0.200…

Q: a. A rectangular, sharp-crested weir 15 m long with end contractions suppressed is 1.60 m high.…

A: As per guidlines we can solve one question at a time, please upload separately, Thanks Solution (a)…

Q: Determine the safe uniform live load that the beam can carry on a simple span of "L" meters with the…

Q: FSs = 2.18 FSO = 1.21 Which failure is more likely to happen? O Safe O Cannot be determined O…

A: Given data: (F. O. S) sliding = 2.18 (F. O. S) overturning = 1.21

Q: Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method.…

A: Given data : E=80 GPa beam section = (150mm*150mm)

Q: 1.A car with an initial velocity of 45 kph and has a uniform acceleration of 5m/s2. Determine the…

A: As per Bartleby policy i can answer only one question at a time. Please upload other questions…

Q: Determine the slenderness ratio of a 5-m steel column, fixed support at both ends, having the cross…

A: We will find radius of gyration and effective length.

Q: The average normal flow of traffic on cross roads A and B during design period are 400 and 250 PCU…

A: given- normal flow of traffic=400 & 250 PCU per hoursaturation flow values=1250 and 1000 PCU per…

Q: An exploratory drill hole was made in a stiff saturated clay having a moisture content of 27.5% and…

Q: 4.144 Find the forces in members HC and HG in terms of P. -1.5 m--1.5 m--1.5 m- A B C D 1 m 2 m H. 3…

A: This problem is related to truss from structure analysis. In this question we find out Force in…

Q: A two-story office building has interior columns spaced at 6.7m apart in two perpendicular…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: What is the moment at the midspan of a one-way floor system to carry a service live load of 13 kPa?…

A: Given LL=13 kPal=6 mγc=23.60 kN/m3

Q: Summarize the difference between soundness test by Le Chatelier method and Autoclave method.…

A: Test for soundness- Certain cement has been observed to expand significantly after setting,…

Q: Figure Q2(b) shows a brass cube with 152.4 mm on a side and weights 298.2 N. In order to hold this…

A: Cube size = 152.4 mm or 0.1524 mWeight of cube = 298.2 NWeight of foam, = 707.3 N/m3

Q: Calculate the noise voltage generated by 5k2, 10 k2 and 15 k2, resistors connected in series. Given…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Concept explainers

Pressure and Stress

Question

Pls answer wt complete solution. Ty asap

What is the balanced steel reinforcement (mm?) of the beam if it has a specified
compressive strength of 27 MPa and steel yield strength of 299 MPa? The width of
the beam is 420 mm and it has an effective depth of 732 mm. Round off only on your
final answer. (3 decimal places)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Choose only correct answer/option.
Problem No. 3A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume Cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement O 0.00182 O 0.00201 O 0.00224 O 000391 O 0.00577
Give me right solution. Urgent please
37 A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 8 kN/m and service live load of 7 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
Thank youu
A beam has a class 3 web and a class 2 flange. When along the stress-strain diagram will it fail, and how? Remember how we define the classes. Make a sketch showing a W-section beam that hasfailedin this way. How can this be prevented?
A 200 mm × 220 mm timber post is subject to an unknown axial compressive load(F) that is eccentric to both principal axes as shown below. If the axial stress is2.4 MPa then:(a) What is the compressive load?(b) What are the applied moments in the x and y directions?(c) What are the moments of inertia in the x and y directions.(d) At what corner does the maximum stress occur? State whether it is tensile or compressive?` (e) Calculate the maximum stress at the corne
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
what is the largest udl that could be applied to a cantilever beam 5m long if the allowable stress is 100mpa in tension, and 120mpa in compression?
R.Bars.
With each part being the same length, and a cross-sectional area of 5.25 in^2, being made of A992 steel, when the temp goes from -10F to 100F how large should the gap be so the rails don't touch? Determine the stress if temp rose to 110F based on gap size Determine if rails would fail with max shear or normal stress