What do the experimental values of Pi suggest about the accuracy of each measuring tool: ruler, vernier caliper, microme
Q: What is the value of the expression 1/2 (3x - 5) +5 when x= -3? A. 2 OB. 4.5 O C. -2 D. 7
A:
Q: 3. Carry out each of the following conversions mg a. 450 µg / mL to mL b. 0.15 g/L to mg/mL 4. A…
A: According to Bartleby guidelines only one question is allowed to be solved at a time therefore I am…
Q: person's blood pressure is measured to be 129±8 mm Hg.129±8 mm Hg. What is the percent uncertainty?…
A: Pressure P = 129±8 mmWe need to determine percentage uncertainity.
Q: Find the precision of the 4th measurement, from the values in the table below No Xn 1 48 2 50 3 52 4…
A: The accurate measurement will be the average value Xnavg = (48+50+52+47+51)/5 = 49.6
Q: The load voltage waveform of a single phase full bridge inverter supplied from 30OV DC voltage…
A: Given:
Q: In the state of Indiana it was once proposed to round the value of a to 3. Using the Percent Error…
A: Since you have asked multiple questions, we will solve the first one for you. If you want any…
Q: A water pipe having a 2.45 cm inside diameter carries water into the basement of a house at a speed…
A:
Q: MEASURED USING CENTIMETER RULER MEASURED USING CENTIMETER RULER Measured Diameter d (cm) Measured…
A: Solution: Calculate the relative uncertainty in diameter for dime. ∆Uddime=0.051.76×100=2.84%…
Q: For every 20 tables Melanie waits on, she makes 40 dollars in tips, how much would she make in tips…
A: It is given that for every 20 tables, Melanie makes 40 dollars in tips It is required to…
Q: Calculate percent amount to three-figure accuracy. (Use one decimal place for the percent value.)…
A:
Q: Volume D.000l m P=66484 प्लरार त O.0000l Relahie Deneily= Den sily Sample Kilm 3 Knokin Densty of…
A: The difference in the experimental value from the standard value is expressed in terms of percentage…
Q: A new drug is metabolized by healthy aduits at a rate of 25% each hour. After 2.5 hours, a patient…
A:
Q: Three students, Tom, Sally and Kevin, did an experiment where the accepted size of nano-particles of…
A: Measurement of length or size is done in units of meter. One nanometer is equal to 10-9 meter. Now,…
Q: how to determine experiment density with of a zinc rod with only the mass, length and diameter, when…
A: Given: Mass of zinc rod, m = 69.5 grams length of rod, L = 34.3 cm Diameter of rod, D=19 cm To…
Q: You repeated a measurement 6 times and recorded the time using a stop watch: 5.6s, 4.6s, 4.8s, 5.1s,…
A:
Q: The main scale of a vernier callipers is calibrated in mm and 19 divisions of main scale are equal…
A: Given that, Number of the divisions of vernier scale= 20 Main scale read = 35 mm = 3.5 cm 4th…
Q: Read the measurement on the Vernier calliper below and determine the absolute error, relative error…
A: Absolute error = Measured value - true value Relative error = Absolute error / true value Percentage…
Q: what is the density experimental and % error of them
A: Required : Experimental density and percentage error.
Q: The results of the analysis of a metal alloy were reported in terms of percent Cu (%Cu). The values…
A:
Q: Max and min that would round to 8.6 oz? What is the uncertainty in the measurement?
A: Given :- weight = 8.6 oz
Q: what is the relationship between precision and uncertianity in a measurement?
A: Measurement Uncertainity has following parameters: 1) Precision : It given an idea about the…
Q: The table shows the set of five measurements recorded in a laboratory. The precision of 2nd…
A: The formula for finding the mean of the given measurement is given by, Here, Σx and n represents…
Q: The mass of an aluminum cube was measured to be (A)=71.2 g. Using the Vernier caliper, the length of…
A:
Q: If you are to measure the length, width and thickness of a book, what measuring device will you use?…
A: According to question: For measuring the length, width and thickness of a book, I prefer Measuring…
Q: Apply the relative error formula and determine it in a calculation of the cross-sectional area of a…
A: Given , Diameter , D = 0.085 ± 0.002cm We know that cross-sectional area , A = πD22 =πD24 Using…
Q: Find the volume of a soccer ball with the following measures: Please, make sure you take into…
A: Given:- The Diameter = 22 cm ±1.0 cm Find:- The volume of the soccer ball?
Q: Here's the aluminum (Al) cylinder: 1 4 Here's the lead (Pb) cylinder: 3. 1. What is your estimate…
A: To determine: Length, volume, density and their uncertainties.
Q: what is the density of aluminum if 3.50 cm3 has a mass of 9.45 g? Please report answer to the…
A: The expression for the density is
Q: 1. Complete the data below for the experiment: Measurement ENGLISH (inch ) 1/16 METRIC ( cm )…
A:
Q: What is the relationship between the accuracy and uncertainty of a measurement?
A: The accuracy and uncertainty are inversely proportional to each other. If the uncertainty is less…
Q: Do random errors contribute to % error and/or standard deviation? Why?
A: Random errors are inherent fluctuations in experimental measurements caused by various unpredictable…
Q: Measured values are usually presented as mean plus or minus uncertainty. If two experimental values…
A: Given Two experimental valuesare (8.1 ± 0.5) and (7.9 ± 0.4) To find out The uncertainty of their…
Q: Question 2: Complete the following Error Analysis The lengths of the sides of a rectangular box are…
A:
Q: A digital micrometer measures the diameter of two cylinders. Cylinder 1 diameter = 15.22 ± 0.02 mm…
A: Uncertainty in difference or addition is given by direct addition of uncertainty in given…
What do the experimental values of Pi suggest about the accuracy of each measuring tool: ruler, vernier caliper, microme
Step by step
Solved in 2 steps with 2 images