What current will flow in a 10 ohms resistor if the voltage wave increases linearly from 50 to 100 volts at t = 0 to t = 0.01 and decreases linearly from -50 to -100 volts during the remaining half cycle.

Q: A half-cycle average voltage of 20 V is equal to what ms voltage?

A: Given: Half cycle average voltage = 20 V

Q: Correct me if i am wrong I have studied different formula formula for saturation current.

A: Both are correct.

Q: 2μA of current flows through a component for 5ms, what will be the charge in that component? Major…

A:

Q: 1-4 A d'Arsonval meter movement with a full-scale deflection current rating of 200 μA and an…

A: Answer: Full-scale deflection current   Ifs = 1 mA internal resistance   Rm = 500Ω of an half-wave…

Q: We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag…

A: a multimeter is a portable device that can be used to take various electrical measurements like,…

Q: If we use 5000 µF, we can get a very low ripple voltage. But this is so bad and this a disadvantage,…

A: According to the given question we are using a 5000 micro farads capacitance , then there is a…

Q: The saw-tooth voltage waveform shown in the figure is fed to a moving iron A. meter. Its reading…

A: Given waveform is - Given meter is moving iron meter.

Q: Question 1: If the current is 1.07 mA at an applied voltage of 606 mV, and the current is 4.05 mA at…

A: Given, The currents, I1=1.07 mAI2=4.05 mA The voltages,  V1=606 mVV2=640 mV The value of thermal…

Q: 12- For the electric circuit shown in the figure (E12), determine the value of (R) if the current…

A: This is bridge circuit Current in AB branch = 0A Find the value of unknown resistance R?

Q: An alternating current was measured by a DC milliammeter in conjunction with a full-wave rectifier.…

A: Given: DC milliammeter reading, Idc=7.0 mA in conjunction with a full-wave rectifier To find: (a)…

Q: 3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1…

A: Note :- As per guidelines we are supposed to answer only 3 sub_parts. So I request you to post other…

Q: Question 2 a. There are several techniques that can be used to measure the high voltage. Explain the…

A: There are several type of method for measure the high voltage. But here we are explain only one…

Q: R; = 10 2 R3 = 8 0 R2 = 62 R4 = 42 9 V Rs= 52 r=0.5 N

A: Find the total resistance of the circuit.

Q: If a voltage waveform has a peak voltage of 88.0V and 4.5% ripple, what is the minimum voltage

A: In this question we need to find the minimum voltage.

Q: The amount of current the battery can produce for a period of 20 hours at 80 degrees Fahrenheit is…

A: An ampere-hour (abbreviated Ah, or sometimes amp hour) is the amount of energy charge in a battery…

Q: Which of the following is NOT a variable in voltametric methods? A. How the current is applied B.…

A: In this question we need to choose a option which is NOT a variable in voltametric methods.

Q: 1- Use the Oscilloscope (CRO) waveforms photos for the circuit in figure 1, to discuss the input,…

A: During On time circuit-:

Q: The relation between electric intensity E, voltage applied V and the distance d between the plates…

A: Given: E = Electric Field ; V = Voltage applied ; d = Distance between Plates

Q: Switch Battery FIGURE 14-21 The resistor helps prevent voltage spikes caused by the inductor.

A: Solution: Let the switch is opened at t=0 Just before the switch is opened i.e t=0- The equivalent…

Q: Describe the characteristic and operation of the meter movement in measuring alternating-current.…

A: The meter movement in an alternating current (AC) meter is a device that is used to measure AC…

Q: An electron moves through a voltage of 9 V from the positive polarity to the negativepolarity. How…

A: Since the electron is moving from positive polarity to negative polarity, the electron will lose…

Q: The current enters to the positive terminal of a device is i(t) = et amps, and the voltage across…

A: Given, Current, it=e-4t A Voltage, vt=3didt               vt=3ddte-4t=-12e-4t V Time, t = 0 to 2 sec

Q: Calculate the peak voltage across R2 in the diagram R1 = 1 kohm, R2 = 680 ohms, supply voltage is…

A: A sinusoidal signal can be mathematically represented as, x(t)=A sin(2πft+ϕ). Where A is the peak…

Q: What will be the value of thermal voltage of Si at 300 K?

A: Write the expression for thermal voltage,

Q: Analyse Figure Q2.1 to determine the voltage with respect to ground at points A, B, C and D. Assume…

A:

Q: What is the effect of decrease in voltage at constant resistance on a current according to ohms law

A: According to ohm's law the effect of decrease in voltage at constant resistance on a current .…

Q: Draw a graph of current against time for two complete cycles of alternating current of peak value 2…

A: The solution is follows.

Q: How much resistance must be put in series with a 40-microfarad-capacitor connected to a 110 volt,…

A:

Q: For solar cell the Open Circuit Voltage (Voc) occurs when O a. voltage is minimium O b. voltage is…

A: Correct option is D) Current is Zero open circuit voltage is the highest voltage for a solar cell…

Q: What potential difference is required across an 8-0 resistor to cause 27.78 A to flow through it?

A: Given, The potential difference, V =? Resistance, R=8 Ω Current, I=27.78 A

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.