What are the logic gates that represents the following tables? INPUT OUTPUT INPUT OUTPUT А В C A B C 1 0 | 0 1 1 0 1 1 1 1 1 1 1 1
Q: 101 0011-01010 in binary equal to.. in octal O a. 121 O b. 111 O c. 51 O d. 52
A: Option : b Answer
Q: Q. A straight binary sequence is applied to a 4-bit DAC, and the output in figure below is observed.…
A: Given: A straight binary sequence is applied to a 4-bit DAC, and the output in the figure below is…
Q: a) The 5-bit parallel binary full adder in Figure 2 performs the addition of two 5-bit numbers, A…
A: The output of 5 bit parallel adderout=0,s4=1,s3=1,s2=0,s1=0,s0=1
Q: Input Present State Next State Flip Flop Excitations Outputs A 01 00 01+ Q0+ J1 K1 JO KOZY X W 000 0…
A:
Q: An IC with two-input logic gate produce a output as LOW, only when all of the inputs are LOW is IC…
A: The logic gate which produces a output as LOW , only when all of the inputs are LOW is known as OR…
Q: The lowest address contained in the ROM memory is: A13- A12- All C B 1 A10- El A 2 ROM 7 CS 0000…
A: The explanation is as follows.
Q: A B Out 0 Cin Cout Please read. In Verilog only uses reg variables and model each gate using an…
A: For the given circuit we have to write the verilog code
Q: Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables…
A:
Q: The waveforms are correct for the logic circuit shown. A D- X- C True False ABC
A: In this question we need to verify the given output waveform of logic circuit is true or false.
Q: Consider a family of logic gates that operates under the static discipline with the following…
A: According to the question, we need to find noise margins The data are given as the following voltage…
Q: Identify each of these logic gates by D A B A B A A B A B - Y Y
A: The given logic gates arei.ii.iii.iv.v.We need to identify the name of the logic gates given.
Q: If the limit Switch_1 is turned ON and OFF two times and then left ON until the end of the day, what…
A: According to the question, for the given PLC system as shown belowWe need to find the content of…
Q: Input Output Minterm Input_SEL Output_y 1 1
A: The given combinational circuit is:
Q: SW1 SW2 a SW3 SW4 LSB 0- 2 I I 4 15 1 1 9 10 12 113 Ofrom logic switch A 31 6 81 11 L1 L2 L3 L4…
A: Given digital circuit is - In this circuit, All the four gates are XOR gate. All the four gates has…
Q: The logic function implemented by the multiplexer circuit is (ground implies a logic "0") 4x1 MUX 1…
A: Given- Multiplexer circuit Ground implies '0' input. To find- The implemented logic function.
Q: Design the given logic function F by using 4x1 multiplexer. a b c F 0 0 0 1 0 0 1 0 0 1 0 1 0 1 1 0…
A: The diagram of 4X1 multiplexer,
Q: is a logic switch that select ******* information from one of the input line and directs it to a…
A: (1) The logic switch that select information from one of the input line and directs it to a single…
Q: 22) The 8-bit registers A, B, C & D are loaded with the value (F2) x (FF) he 39) hes hex and (EA)…
A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…
Q: A full adder function is given in Figure 1(a). Implement this function using decoder 74x138 given in…
A:
Q: In a 4-bit system, what are the carry and overflow flags of the following operations: a. 0100 +0010…
A: In this question, we need to determine the carry and overflow flags of the given addition.
Q: Question1: Read the following table, and design a logic circuit that can convert the binary code…
A:
Q: Q2Q1 What are the simplest logic expressions for J2 and K2? Do not use XORs. Variable "A" is an…
A: We need to find out simplified Boolean expression for given k map .
Q: In logical gates, the output of the |
A: The output equation of the AND gate of the A and B input is = AB The output equation of the OR gate…
Q: Logic gates from logic family are suitable for VLSI circuits a. CMOS O b. ECL O c. MOS O d. TTL
A: We use CMOS logic family for VLSI circuits. It is having low power dissipation so used in vlsi…
Q: Create a relay logic diagram for the ladder diagrams in the following problems. 47. L1 L2 48. LI A B…
A: Plc ladder diagram
Q: This is a block diagram of 4-bit adder. Show how binary number 1101+1001 is added. Write the values…
A: The four-bit adder can be implemented using the one-half adder and three full adders.
Q: Logic gates from logic family are suitable for high speed operations O CMOS O TTL O MOS O ECL
A: Correct option is ECL ECL is the kogive family are suitable for high speed operations. It is…
Q: Q13/Assume that the microprocessor can directly address 64K with a and 8 data pins The memory map…
A: We need to design a 16K x 4 , by using of 4K x4 memory .
Q: Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables…
A: The Code Converter is a tool for converting one binary code to another. Binary codes come in a…
Q: Perform floating point binary addition to the following: A: 1 10000011 10110111010000000000000 B: 0…
A: We need to perform floating-point binary addition to the following: A:…
Q: Trace the subtractor's logic when performing 2- 5. а3 а2 а1 а0 b3 b2 b1 b0 a3 a2 a1 a0 b3 b2 b1 b0…
A:
Q: 4- Assume the following input level of parallel full adder A4 A3 A2 A1 Ao = 10010 , B4 B3 B2 BỊ Bo =…
A:
Q: Logic circuit Design combinational logic circuit that takes 7 bit numbers and an input and output…
A: A combinational circuit is a digital circuit whose output is solely determined by its present input…
Q: register is used for ..... counting purposes like loops no one O AX and ALO AX O all registers O AL…
A: Cx register used for for counting purpose in 8086 microprocessor. Ax and AL used as an accumulator…
Q: The output of a logic gate is 1 when all its inputs are at logic O, the gate is eithe
A: We need to find output of a logic gate is 1 when all its inputs are at logic O, the possible gates…
![What are the logic gates that represents the following tables?
INPUT
OUTPUT
INPUT
OUTPUT
A B
A
В
C
1
1
1
0 1
1
1| 0
1
1
1
1| 1](/v2/_next/image?url=https%3A%2F%2Fcontent.bartleby.com%2Fqna-images%2Fquestion%2F898bc690-c0c1-4496-9ea8-7403674c6c7c%2Fb7b7fd5b-2825-49a3-abf0-53508a573d21%2Fyf9sf08_processed.jpeg&w=3840&q=75)
![](/static/compass_v2/shared-icons/check-mark.png)
Step by step
Solved in 2 steps with 2 images
![Blurred answer](/static/compass_v2/solution-images/blurred-answer.jpg)
- (c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).Q If we want to design a logic circuit that make selective set for example, the number (0001) to become (0111) O using XNOR gate with the same number as input O using XOR gate with the 0111 number as input using AND gate with the 0111 number as input using OR gate with the 0110 number as inputIn a 4-bit ripple up-counter how many clock pulses will you apply, starting from state 0 0 0 0, so that the counter outputs are as follows? (a) 0010 (b) 0111 (c) 1001 (d) 1110
- answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.Question1: Read the following table, and design a logic circuit that can convert the binary code from 2421 to Excess-3. Four Different Binary Codes for the Decimal Digits Decimal ВCD 8421 Digit 2421 Excess-3 8, 4, –2, –1 0000 0000 0011 0000 1 0001 0001 0100 0111 0010 0010 0101 0110 3 0011 0011 0110 0101 4 0100 0100 0111 0100 5 0101 1011 1000 1011 0110 1100 1001 1010 7 0111 1101 1010 1001 8 1000 1110 1011 1000 1001 1111 1100 1111 1010 0101 0000 0001 Unused 1011 0110 0001 0010 bit 1100 0111 0010 0011 combi- 1101 1000 1101 1100 nations 1110 1001 1110 1101 1111 1010 1111 1110
- Hello I am having trouble with a practice problem for my digital circuits class. I would appreciate if you can help me out. Thanks.Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).A 4-bit binary up/down counter is in the binary state of zero. The next state in the DOWNmode is (a) 0001 (b) 1111 (c) 1000 (d) 1110
![Electric Motor Control](https://www.bartleby.com/isbn_cover_images/9781133702818/9781133702818_smallCoverImage.gif)
![Electric Motor Control](https://www.bartleby.com/isbn_cover_images/9781133702818/9781133702818_smallCoverImage.gif)