Well No. WHP (psi) Pwf (psi) Q (bbl/day) 1 450 2000 200 2 500 2000 600 3 240 1300 1000 4 320 1650 2000 5 240 1400 3000

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: What is the formula for crushing efficiency, given specific surface area of a product, mass…

A:

Q: A square polymer sample of edge length 80 mm is subjected to a force of 6400 N. The resulting stress…

A: Given data: Length of edge of a square = 80 mm Force = 6400 N

Q: A single crystal of a metal is oriented for a tensile test such that its slip plane normal makes an…

A: Given,

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: In general, why should the operating pressure be high and the operating temperature be low for an…

A: The reason for the high pressure and low temperature for the absorption process is to be mentioned…

Q: For a monosized media filter with a particle size of 2.5 mm in diameter, a bed depth of 2 m and…

A: Given data: Diameter of particle = 2.5 mm Depth of bed = 2 m Porosity = 20 % Water temperature = 15…

Q: A cylinder has a of 0.35 MPa. What i

A: The minimum allowable thickness is thickness of sheet required to sustain pressure of system

Q: Ex: A well is need to be drilled to 15,000 ft. The entrance into abnormal pressures at 10,000 ft are…

A:

Q: A solid cylinder of weight 9 kg slides in a vertical lubricated pipe. The clearance between the…

A:

Q: Fraction of water

A: To Answer whether the fraction of water in the underflow stream of thickener is zero

Q: (2020 psi), compute the critical resolved shear stress.

A:

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: Convert a viscosity of 20 (g)/(cm)(s) to the American Engineering units (Ibr)(hr)/(ft?)

A: Given viscosity is 20 g/cm s Viscosity unit of g/cm s have to convert into American Engineering unit…

Q: 3. Define the hydraulic and energy grade lines, and explain the method of calculating and drawing…

A: It is asked to define the Hydraulic grade line and energy grade line  and explain the method of…

Q: Determine the surface area required for a rectangular settling tank for a wastewater flow rate of…

A: The surface area required by the rectangular settling tank for the given flow rate of wastewater is…

Q: (Show complete solution) For flow of water at a Reynolds numver of 1.03x106 through 5-cm diameter…

A:

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: A single crystal is oriented such that the normal to the slip plane and the slip direction are at…

A: Angle between normal to slip  = 60 0 Angle of slip direction = 350 Critical resolved shear stress =…

Q: A tensile stress is to be applied along the long axis of a cylindrical steel rod that has a diameter…

A: Given data: Diameter of rod = 0.015 m Change in diameter = 1.5×10–3 mm Value of Young’s modulus for…

Q: If I want do a certain application in the process engineering, what is the best type of pump that…

A: Classification of pump:

Q: 10) For Newtonian fluids, the relation between the shear stress and the rate of deformation (du/dy)…

A: For Newtonian Fluid.  Shear Stress =  τ = μ dudy  where,   dudy = Rate of deformation or shear rate…

Q: ne equivalent permeability of four beds in series, having equal formar thickness under the following…

A: To calculate Equivalent permeability of four beds in series having equal formation thickness under…

Q: 2. (a) 4 m, a width of 6 m and U = 1.8 m/s. For one side of the plate, find: Air at 40 °C and 1 atm…

A: 2(a) Given, The length, L = 1 m The velocity, U∞ = 1.8 m/s The width, w = 6 m The temperature, T =…

Q: 2. 6 The diameter of a cylindrical core sample is 2. 5 cm, its length is 6. 0 cm. Under a pressure…

A: Given data: Diameter of cylindrical core = 2.5 cm Length of core = 6 cm Pressure difference = 0.3…

Q: (b) The general characteristics of three oil wells selected for artificial lift as production method…

A: Table of 3 well are given.

Q: 2. Ethanol at 273.15 K is flowing on a 2-boundary set-up. The top plate is moving at a rate of 20…

A: The shear rate is the ratio of the velocity of the upper plate and the thickness of the film. The…

Q: What

A: The hydrosphere is combined mass of water on ,above and below surface of earth.

Q: Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0064 m.…

A:

Q: What is the maximum radial distance traveled by any particle in cyclone seperator?

A: Chemical processes consist of the separation stages in which the process streams are separated and…

Q: A centrifuge bowl shall separate 2 immiscible liq, SG = 1.1 & SG = 0.9  The diameter inside of the…

A: Given Data  The specific gravity of the two immiscible liquids are given  as :SG = 1.1 , Therefore,…

Q: What is the difference between permeability and permeance?How are they analogous to diffusivity and…

A: The difference between the permeability and the permeance is to be mentioned along with the relation…

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: The strain of a component, which has a tensile modulus of 6 X 105 MPa, and subjected to a stress of…

A: The strain of the component with the given tensile modulus is to be determined.

Q: Torsional stress is also a A Axial stress B Shear stress C Bearing stress D) Thermal stress

A: Given data  Torsional stress is also a _.

Q: Sketch the cross flow induced-draft cooling tower and illustrate all its parts.

A: Induced draft cooling towers Induced draft cooling towers are of two types based on the nature of…