formation.  A cold-wo

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: ind modulus of elasticity of a brass rod of length 200 mm which is subjected to a tensile stress of…

A:

Q: What is the formula for crushing efficiency, given specific surface area of a product, mass…

A:

Q: A square polymer sample of edge length 80 mm is subjected to a force of 6400 N. The resulting stress…

A: Given data: Length of edge of a square = 80 mm Force = 6400 N

Q: A 10mm diameter tungsten cylindrical bar should fit a 9.988mm hole contained in a steel plate.…

A:

Q: 16. What is the unit of resistance in SI? O w O W/K O m-K/W O W/m^2-K O K/W

A: Asked;  SI unit of resistance

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: In general, why should the operating pressure be high and the operating temperature be low for an…

A: The reason for the high pressure and low temperature for the absorption process is to be mentioned…

Q: If the temperature profile in a rectangular slag is represented by: T(x,y,z)=x2-2y2+z²-xy+2yz…

A: The points where spacial derivatives wrt to time are 0 will be where Temperature won't change. We…

Q: A 10-mm-diameter Brinell hardness indenter yielded a hardness of 350 HB when 1250-kg | s used on a…

A: ASTM E10 defines the Brinell hardness test technique, which is used to determine Brinell hardness.…

Q: The centrifugal pump is most widely used in the chemical industry. Sketch the internal structure and…

A: Introduction A centrifugal pump converts rotational energy, often from a motor, to energy in a…

Q: The computed stress should be lower or equal to the allowable stress for the material to be safe in…

A:

Q: A polished stainless steel surface is electrically heated form the bottom to boil water at…

A: Material = Polished stainless steelPressure, Temperature,

Q: Q.3 a). A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…

A: The magnitude of load is to be calculated.

Q: Water at 150 °C flows on the inside of a 1 meter long 2" Schedule 80 steel pipe (thermal…

A: Dear User, Kindly note that according to bartleby policy, we can answer only 3 subparts from the…

Q: 3.) A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension…

A: Given: Length of steel bar=100 mm=100×10-3mCross section of the steel bar=20 mm=20×10-3mForce=89000…

Q: Q1: Recommend the types of materials that should be used in the fabrication of a wind turbine for…

A:

Q: If the entering velocity is 6 m/s, calculate the length of tube and determine whether the process is…

A:

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: A single crystal is oriented such that the normal to the slip plane and the slip direction are at…

A: Angle between normal to slip  = 60 0 Angle of slip direction = 350 Critical resolved shear stress =…

Q: Enumerate the parts/components of a double-pipe heat exchanger and state their functions.

A: Components or parts of a double pipe heat exchanger are shell with nozzles, tubes, expansion joint,…

Q: If the area under the stress and strain curve is less then it is concluded that the material has low…

A:

Q: Create a problem set of 5 problems about material balance. ( Show your solution in each problem)

A: 5 Problems about material balance

Q: On Mars, people live in domes. The outside of the dome walls are made of aluminium. However, the…

A:

Q: 6. Which ratio of cathode to anode accelerates galvanic corrosion? a. Larger cathode to smaller…

A: In general, the rate of corrosion is significantly impacted by the relative sizes of the cathodic…

Q: True or false 1. Electrical conductivity of copper is very low

A: Electrical conductivity is the measurement of the transport of the electric charge through the…

Q: A tensile stress is to be applied along the long axis of a cylindrical steel rod that has a diameter…

A: Given data: Diameter of rod = 0.015 m Change in diameter = 1.5×10–3 mm Value of Young’s modulus for…

Q: We wish to produce 0.2-in-diameter wire of copper having a minimum yeild strength of 60,000 psi and…

A:

Q: The following creep data were taken on an aluminum alloy at 48 °F) and a constant stress of 0 psi).…

A: Given -creep strain vs time data for an Al alloy at a certain stress and temperature  To find steady…

Q: 10. A 6,000 lb of a material goes through a crusher and grinder per hour in succession (on the same…

A: Given that- Mass flow rate of material is,  m= 6000 lb/hr=6000 lbhr× 1hr3600 s=1.666 lb/s Rittinger…

Q: What does a HYSYS fluids package represent thermodynamically

A: In chemical engineering, there are many calculations that can be done manually. But some are very…

Q: A core sample is saturated with water, Weight of saturated sample in air is 22.5 g. Water-saturated…

A: Bulk volume of the sample is volume of the water trapped between the pores of the sample. The weight…

Q: Effect of the carbon percentage on the shape and magnitude (mechanical properties) of stress-strain…

A:

Q: Cl the dimensions were all the same, which chocolate can withstand the greatest load? D. Which has…

A: C. The chocolate that can withstand the greatest load is to be mentioned.

Q: Sketch the (220) plane for CaF2

A: x y z INDICES 2 2 0 RECIPROCAL  1/2 1/2 1/0 INTERCEPT 1/2 1/2 ∞

Q: The figure shows the stress strain graph for 4 materials: 1) the most ductile is? 2) the most…

A: 1) 'C' is the most ductile.More the area under the curve more the ductile. 2) 'B' is the most…

Q: wire 10 m long has a cross-sectional area 1.25 x 10-4 m2. It is subjected to a load of 5 kg. If…

A: As we know  Youngs modulus = stress/strain  Stress= force/area  Strain= change in length /initial…

Q: Reynolds analogy is preferred over Chilton-Colburn analogy. O True False Depends on Sh O Only for…

A: Chilton Coulburn analogy is widely successful analogy used for estimating mass transfer…