Answered: weights are added to bourdon gauge the…

Engineering

Mechanical Engineering

weights are added to bourdon gauge the reading on the of the gauge should be (assuming no error )

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Related questions

Q: 1.3 At the foot of a mountain a mercury barometer shows a reading of 760 mm. A similar barometer at…

A: Given Data- Pressure at Top 500mm of Hg Pressure at bottom 760mm of Hg Density of air =1.223kg/m3 We…

Q: ア-1) P2 , the units of temperature can be: D. When using the equation, %3D 1. Fahrenheit II. Celsius…

A: The thermodynamic, or Kelvin, the scale of temperature utilized in SI has its origin or zero…

Q: Heat can be expressed in the following unit(s): Select all that apply. a newton x meter b…

A: This question is based on the concept of heat from thermodynamics.

Q: 1.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: converting units and calculating the up-lift force of a hot air balloon.**1.1 Converting units (37.1…

Q: If an oil with density of 800 kg/m³ (instead of mercury as Torricelli did) is used to measure…

A: Find the hight of tube . Given data:- Density of oil = 800kg/sec

Q: 0.5mlm 1. 2 3 4 5 cm mm Consider the steel ruler shown. Which of the following dimensions can be…

A: Given: A ruler,

Q: 1-84 Afluid has a dynamic viscosity of 1.2(10-3) N · s/m?. Express its dynamic viscosity in U.S.…

A: The conversion of unit of force from MKS to FPS system, The conversion of unit of length from MKS…

Q: With Cartisian coordinates, express a force vector F, where 01 40°, 02 = 40°, and F = 480 lb. %3D…

Q: Question 3 A set of weight measurements and their expected values are given below, Expected Weight…

A: Given: Full scale deflection→FSD=15 Kg And in the table there are various values of the expected and…

Q: B. 2 m Fg = 600 N 3.5 m 0.5 m Fc= 450 N 1.5 m 1 m 0.5 m 1.5 m

A: Writing the co-ordinates of the points, A≡(0.5,-1.5,0)B≡(-1.5,-2,2)C≡(-1.5,1.5,3.5) Determining the…

Q: 19.7 psia is equivalent to which of the following gauge pressures? Pabsolute Patmospheric P +P 5 pig…

A: 1) Problem number 1 given data l, mass = 15000 lb , density = 7.85 lb/gal we have to find volume…

Question

If a 5.5 kg weights are added to bourdon gauge the reading on the of the gauge should be (assuming no error )

Select one:

a. none

b. 0.171224 N/mm2

c. 171.22KN/m2

d. 0.01746 KG/mm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1. The tank in Fig. 1 contains oil of specific gravity 0.75. Determine the reading of gauge A in KPa. Air 22.9 cm 304.8 cm Oil sp gr 13.57 Fig. 1
If the vernier gauge reading for a specimen is 22.24 mm and DTI observation in divisions are 7, 0, & -2 respectively, find the actual size of the specimen in mm. The actual size of the specimen (in mm)=
For each of the following statements, answer TRUE or FALSE and explain your answer briefly. In the calibration of analytical balance for scale value, the measured mass is directly compared to the nominal value of standard mass.
The pipe assembly of the figure is supported by a fixed support at point A. A couple-moment and a force are applied at points B and C, respectively. In Cartesian coordinates, the applied couple-moment is MB = -150 k N-m, and the applied force is Fc = + 200ĵ Newtons. You may neglect the weight of the pipe assembly. 1. Draw a FBD which is suitable for solution of this problem, when seeking the unknown force and moment reactions at the fixed support, Point A. You may use the existing drawing given below. Your FBD must clearly/correctly show the force and moment reaction vectors. Use double arrowheads to distinguish moment vectors from force vectors. 2. Calculate F°MA, which is the moment generated at A due to the force applied at Point C. 3. Write the equations of equilibrium and solve to find the reactions at Point A. Specifically, find the force-reaction vector, A and the moment-reaction vector, *MA-
In the pressure measurement experiment, for the inclined manometer the elevation angle is 54°. If P1 is equal to 392 mmH20 and P2 is equal to 67 mmH20 then the Adjusted mmH2O is : Select one: a. 30.6 mmH2O. O b. 70.2 mmH2O. O c. 54.2 mmH2O. O d. 45.2 mmH2O.
The gauge pressure of a pneumatic cylinder reads 40 lb/in.2 when the volume is 30 in.3. The cylinder is compressed until the gauge reads 60 Ib/in.?. What is the volume in the cylinder after the gas is compressed? (round to the nearest whole number # #)
A The Crosby gage tester shown in the figure is used to calibrate or to test gages. When the weights and the piston together weigh 105 N, the gage being tested indicates 150 kPa. If the piston diameter is 30 mm, what percentage error exists in the gage?
Convert a pressure measurement of 20 PSIA into units of inches water column (gauge) (A) 1321” H2O (B) 510.1” H2O (C) 701.2” H2O (D) 146.7” H2O (E) 960.5” H2O
Water is flowing through a pipe. A pitot-static gauge registers 3 in of mercury. What is the velocity of the water in the pipe in m/s?A. 2.85B. 4.33C. 3.86D. 5.72
Please answer immediately thank you
Please answer the problems. Show the complete solution.
The local atmospheric pressure is 757.8 mmHg. Express 1.254 atm absolute in terms of (a) dynes/cm2 absolute and (b) psi gauge.