A The Crosby gage tester shown in the figure is used to calibrate or to test gages. When the weights and the piston together weigh 105 N, the gage being tested indicates 150 kPa. If the piston diameter is 30 mm, what percentage error exists in the gage?

Q: The following figure shows a balance used to measure the mass of an orange cylinder. Read the value…

A: Given Data⇒ Main scale reading=20 kg Secondary scale reading=2 unit ±1 gram tolerance has been given…

Q: Vhat is the accuracy for the given scale in meter (m)? 0 0.5 1.0 1.5 2.0 cm

A: Given,

Q: Suppose that the length of the steel bar is measured by a number of different observers and…

A:

Q: 1) Calculate the extension e of the hinge line of brachiopod shell using the fol formula. e = Here,…

A: givenpart1lo=5.5cml1=6cmpart2ψ=90-θand θ=45o

Q: on 2(a) : surveyor's tape is to be used to measure the length of a line. The of 2 cm by 0.5 cm and a…

A:

Q: 0.5mlm 1 3 4 5 cm mm Consider the steel ruler shown. Which of the following dimensions can be…

A: The least count of the ruler is 0.5mm, therefore, the ruler can only accurately measure measurement…

Q: e pressure difference between 2 points is 100,000 Pascals of a fluid column with height of 4 meters.…

A: we will use hydro-static pressure gradient law

Q: cross-sectional area = 150 mm2. During testing, the following force and gage length data are…

A: To Find : (b) yield strength, (c) modulus of elasticity, (d) tensile strength, and (e) percent…

Q: Vertically 300lb/pulg2 and horizontally 150 lb/pulg2 I have only this data please answer.

A: Giver:- My=300 lb/pulg2 Mx=150 lb/pulg2   To find:- Resultant

Q: The measurement 0.000 004 3 m, expressed correctly using scientific notation, is

A: Scientific notation  0.0000043 m = 4.3 *10^-6 m

Q: Using only Table A (Conversion of Units), calculate the values asked.  All answers must be given…

A:

Q: Carbon dioxide flows steadily at 1 kg/s through a device where the pressure, specific volume, and…

A: Given   Mass flow rate, m = 1 kg/s            Pressure, P1 = 200 kPa            Volume, V1 = 0.5…

Q: (200 lb)(0.6 ft)+PABcos30°(0.75 ft)PAB==0184.752 lb  Can you please show all the numbers in this…

A: The above step mentioned in the calculation to find the force in the link AB If we take the moment…

Q: image below, the force acting he box is F = (C · s²) Determine the work done by force F to the box…

A: Given       Force, F = C. S2  Distance, s = 1.7 Constant, C = 6 Find    Work done, W

Q: For each of the following statements, answer TRUE or FALSE and explain your answer briefly.   In…

A:

Q: Question 2(a): A steel surveyor's tape is to be used to measure the length of a line. The tape has a…

A: Dear student,                     According to the guidelines, I am allowed to answer only one…

Q: 1.The thickness of a gage block is measured five times using an instrument that has a resolution of…

A:

Q: 2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then…

A: Mean calculated is 5.9+6.12=6Now calculate deviation from mean S.no      Deviation from…

Q: Calculate the total volume of the cylindrical component below (not to scale): L1 D1- D1 = 1.12 cm D2…

A: Given - D1 = 1.12 cm = 0.01120 m D2 = 0.71 cm = 0.0071 m D3 = 1.58 cm = 0.0158 m L1= 18.68 cm…

Q: The Crosby gage tester shown in Figure 4 is used to calibrate or to test pressure gages. When the…

A:

Q: Q1. As shown in the image below, the force acting on the box is F = (C. 8²) s²) N, where constant C…

A:

Q: Answer the following a. How many significant flgures are there In the following Ilnear measurement?…

A: Since we only answer one question at a time, we will answer the first one. Please resubmit the…

Q: A thermometer reading 10°C is brought into a room with a constant temperature of 33°C. If the…

A: Given data as per the question Room temperature =330 c Reading of thermometer after 3 minutes =150 c

Q: The least count of the main scale of a screw gauge is The minimum number of divisions on its…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: 12 The density of a solid is its mass divided by its volume. If the measured as 42.5 ± 0.5 g and the…

A:

Q: The figure below shows a uniform right triangle of sides lengths a (horizontal) and b (vertical).…

A:

Q: A stick of butter at 35°F measures 1.25 in. × 1.25 in. x 4.65 in. and weighs 4.0 ounces. Find its…

A:

Q: 3.Length and diameter of a bearing are equal (d=L). This bearing should be able to withstand the…

A: Given data: The length and diameter of the bearing is d=L The allowable support force is F=80 N The…

Q: 1. Determine the reading on the vernier scale as indicated by the arrows.

A: According to scale Main scale reading = 41 mm Least count = 1/20= 0.05 mm Vernier scale = 5*0.05=…

Q: The density of a solid is its mass divided by its volume. If the mass is measured as 42.5 ± 0.5 g…

A: In this problem we will calculate the worst possible error in the calculated density for that first…

Q: Convert 0.226 ug into mg. Report answer in scientific notation. The decimal part is expressed with…

A:

Q: 1. During a tensile test in which the starting gage length =125.0 mm and the cross-sectional area =…

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.