We wish to design the circuit shown in figure for a voltage gain of 0.9 with a power budget of 4 mW. Compute the required value of W/L. Assume C₁ is very large and λ = 0. We want to design the circuit shown in the figure with a power consumption of 4 mW and a voltage gain of 0.9. Calculate the required W/L value. Assume that C1 is very large and λ = 0. Circuit parameters UnCox = 200 μA/², VDD = 1.8 V, VTH = 0.4 V, R₂ = 50 2 VDD=1.8 V Vin 1₁ O a. 45563 O b. 40500 O c. 28038 O d. 36450 O e. 52071 O f. 33136 O g. 26036 Oh. 30375 M₁ C₁ HH w RL Vout

Q: The is known as the final control element . -

A: The final element in the control system is that element which is responsible or the output of the…

Q: What is the difference between continuous wave and pulse wave transducers? This is for DMS 101…

A: The difference between the continuous wave and pulse wave transducers is explained by the following…

Q: If the line frequency is 50 Hz, the output frequency of a bridge rectifier is

A:

Q: 4. The problems are: A circuit including three kinds of storage elements is shown in Figure 1. A:…

A: As per the guidelines, I am solving the first question (A). Please post the next question separately…

Q: loop operation is followed in SMPS operation.

A: Open loop

Q: The signal is sampled with sampling time interval of 5 seconds then the time period of the message…

A: The sampling frequency should be at least twice the message signal frequency. fs≥2fm The sampling…

Q: Digital Electronics Q1): Draw the timing diagram showing the Q output of each F.F (Q0, Q1): HIGH FFO…

A:

Q: Determine the frequency of an free running oscillator circuit given that R₁ = 3N, R₂ = 2.7 kN and C…

A:

Q: The signal in the shown figure is Amplitude Time Amplitude modulation O Frequency modulation Phase…

A:

Q: The most common standard electronic current transmission signals range fron to mA.

A: The most common standard signal for electronic transmission is 4 to 20 mA.

Q: In radiation triggering when the intensity of light Obecomes more than Obecomes less than Obecomes…

A: This question is based upon the triggering methodology of Thyristors , the are various methods to…

Q: In control system, the input signal is generally represented as

A:

Q: -By Michelson interferometer we can determine

A: Given   We need to enumerate what can be determined by using Michelson interferometer. Please find…

Q: Q3 An AC bridge is shown in Figure Q3. It has an AC excitation input and four arms of impedances,…

A:

Q: Noise caused by random fluctuation of electrons in an electronic device is

A: In the electronic devices noise unwanted signal that is superimposed on the input signal and then…

Q: Fast video ADC's are used in digital oscilloscopes O TV tuner cards software defined radio…

A: According to the question we have to find the use of fast fast video ADC.

Q: Differentiate between absolute instruments and secondary instruments

A: Different between absolute instruments and secondary instruments:   Absolute instruments…

Q: A diode is O a. a unidirectional switch

A:

Q: Which is correct in case of Computer controlled system?

A: Given Data:There are 4 statements regarding computer-controlled systems.Required Data:Here, we need…

Q: which error characteristics of an instrument has different response after adding an instrument for…

A:

Q: . The phase shill oscillator depends on Teedback....................

A: The phase shill oscillator depends on POSITIVE Feedback.

Q: 3.Explain about Lead compensator and Lag compensator in detail

A:

Q: Ex. 304 See Figure 280. G(s) =1007( (s+2)(s+ 6) ), H (s) =1, and R(s)=1/s (unit step input).…

A: It is given that: Gs=100s+2s+6Hs=1Rs=1s

Q: How do you clear a new EPROM?

A: We need to tell about how do we clear a new EPROM.

Q: What is the accuracy of bellow sensor? O a. ± 1% O b. ± 0.001% O c. ± 0.1% O d. ± 0.01%

A: At high differential pressures the accuracy is around 1.5% of the measuring range.  and At lower…

Q: Question 12 The output frequency of a half-wave rectifier is twice equal to O half the input…

A:

Q: (b) A 555 timer connected as astable multivibrator with Rl-15 k2, R2-100 k2, ar Cl=0.02uf. Draw the…

A:

Q: output waveform of a rectifier is called a/an

A: We need to tell about output of rectifier

Q: Write an AVR program using the timer to generate a square wave at a frequency of 50KHZ knowing that…

A: // Program to Generate waveform using AVR Microcontroller Timers #include<avr/io.h>…

Q: A Voltage Event Recorder (VER) is a device that records voltage fluctuations.

A: VER used for voltage fluctuations.

Q: are very sensitive moving coil instruments.

A: In this question , we will find which is very sensitive moving coil instruments..

Q: Solve all questions, please.

A: In this answer let us try to answer the given questions as shown below.

Q: Q4. a) b) Figure 7 shows a phase-shift oscillator. Explain briefly how the phase shift required for…

A: the phase-shift oscillator circuit shown in Figure 7.a) Achieving Sustained Oscillation with Phase…

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.