We have steam at 10 bar flowing in a line. We open a valve attached to the line and the steam comes out to 1 bar at 100 C. a) is this possible? b) What is the state of the steam in the line ...compressed liquid, saturated mix, superheated vapor?

We have steam at 10 bar flowing in a line. We open a valve attached to the line and the steam comes out to 1 bar at 100 C. a) is this possible? b) What is the state of the steam in the line ...compressed liquid, saturated mix, superheated vapor?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Well-insulated ducts operate at steady state with parameters as shown. The pressure is about 1 atm everywhere. Ignore potential and kinetic energy effects, take the dead state as 14.7 psi and 540°R, and assume ideal gas model for air with c, = 0.24 Btu/lb.°R. a. 0I What are the mass flow rates for each state (1, 2, and 3), in lb/min? b. What is the exit temperature, T3, in °F? 0] Find the rate of entropy production within the duct, in Btu/min-°R. d. Find the rate of exergy destruction within the duct during this process, in Btu/min. C. D = 4 ft V = 400 ft/min T = 80°F V3 = 400 ft/min T3 = ? D3 = ? Insulation (AV), = 2000 ft³/min V, = 600 ft/min T, = 40°F Page 2 of 3
I need help thermodynamics review problem! thank you Steam at 440K, 100 kPa, with a mass flow rate of 0.164 kg/s enters an adiabatic mixing chamber and mixes with 10.00 kg/s of water entering at 325 K, 100 kPa to produce an exit stream of water at 100 kPa. Assuming a steady state steady flow process, determine: a) The mass flow rate (kg/s)at the exit.b) The water exit temperature (K).c) The exit velocity (m/s) if the circular exit pipe diameter is 0.03m.
I need help with a review porblem I cannot solve! thank you Steam enters an adiabatic turbine at 4 MPa, 800K and exits at 8 kPa, 90% quality. Assuming steady state, steady flow conditions, determine: a) The power output of the turbine (MW) if the mass flow rate is 63kg/s. b)The volumetric flow rate at the inlet (m3/s).
A steam pipe carrying 400C, 200kPa steam enters a well-insulated mixing chamber where it is mixed with a 30C, 200kPa stream of cold water with twice the mass flow. a) what is the enthalpy of the exit stream? b) what is the quality of the exit stream?
This is an Isothermal Compression of Ammonia [not an ideal gas] Ammonia in a piston-cylinder device initially at 700kPa, 303K undergoes a reversible isothermal compression process until the volume is reduced to 25% of the initial volume. a) Draw the process T-s and p-v-diagrams, relative to saturation lines. b) What is the heat and work per unit mass?
1. Heat Transfer Problem: We want to generate steam at 300 C 20 bar at 1000 kg/min from water at 60 C, 20 bar. To do this we will use oil at 500 C which will leave the steam generator at 350 C. (Cp = 0.9 cal/g-C) What is the rate of oil required?
Calculate the energy requirement to raise the temperature of 1 kg of water from 60 ° C of water to 100 ° C using the following approach; a. Use of mean specific heat = .... kJ. b. Enthalpy change in water - vapor saturation table = .... kJ.
Determine the amount of work required to compressed 1.5 kg of air at a pressure of 7 barg. The isentropic index is 1.2 and the air intake is at 1 bar, 20C & RH =65%. i) Find the temperature at the end of the compression. ii) Represent the above process on a p‐v diagram. iii) If the isentropic efficiency is 65%, find the indicated or real work. iv) Find the shaft work needed if the mechanical efficiency is 75%.
You have a tank that is 0.01 m^3 and is initially evacuated. You then hook this up to a line that supplies N2 at a pressure of P_1 = 5 bar and a T_1 = 350 K. The tank fills adiabatically (you can assume there is no heat flow to the walls of the tank), and the filling ends when no more N2 flows into the tank. Find a) the final pressure of the gas in the tank, and b) the final temperature of the gas in the tank. You can assume N2 is an ideal gas with a CP* = 29 J/mol K. NOTE: Mainly I am confused on how the evacuated tank factors into the work for b). What I did was use the ideal gas formula to find a value for N2*T2 (601.395) but I am no longer certain how to continue in the work. I was assuming the practice question had meant the temperature of the tank was 0 initially but it leads to a negative mole value. For a) I got 5 bar, arguing the flow would stop when the pressure of tank and line are equal
4.3 Outside air (100°F/75°F) flowing at 1000 cfm is mixed with return air (75°F/63°F) at 5000 cfm. Find the mixed air conditions (db, RH, wb, v, and h). Sketch on the psychrometric chart.
A heat exchanger uses medium pressure steam at 10 bar and 350 C to heat cyclohexane vapor from 100 C up to 275 C as shown in the figure below. The steam is available at a flowrate of 32 kg/h and it condenses completely in the heat exchanger and exits as saturated liquid condensate at 10 bar. a) How much heat (in kW) can be provided by the steam? b) How much cyclohexane can be processed in kg/h? Vapor Cyclohexane T = 100 C P = 1 atm Steam T = 350 C = 10 bar Condensate P Vapor Cyclohexane T = 275 C P = 1 atm P = 10 bar
1. Find the thermodynamic property value requested for each of the following. Enthalpy and entropy are mass-specific values. Also tell me what you have – ideal gas, superheated vapor, saturated vapor, saturated liquid-vapor mixture, saturated liquid, or compressed (subcooled) liquid. C. Find the specific volume for liquid water leaving the feedwater pump at a pressure of 120 bars and a temp of 90 °C. Use tables for steam (water)