65 psia is expanded irreversibly through a turbine that has an efficiency of 0.7 antil the pressure is reduced to ambient pressure. ) What is the actual work produced by the turbine? ) Find the final temperature using the steam tahles

Q: Q243 For the force system shown in figure C24); determine The magnitude and location of the…

A:

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: The hollow cylinder shown in Fig. P.14.22 is built-in at one end and carries a vertical load of 2 kN…

A: The bending moment due to force is - M=2×1 kNm=2000×1000 NmThe twisting moment due to force is -…

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: 2. EVALUATE dx e

A: The indefinite integration is represented by ∫f(x)dx and the solution is F(x)+C, where F(x) is…

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: 1) Resolve the force F into components along the a and b axe agnitudes of these components. (Use:…

A: given:

Q: The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as…

A:

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: H G 60 E D 7 kN 7 kN 9 kN 6m 6m 6m 6m

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: F 1000 lb y 500 lb 45° 30°

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: determine (a) the required value of a if the wn is to be vertical, (b) the corresponding 30° 200 N

A:

Q: Q2/ As shown in fig.(2). Prove the main equation for the coefficient of frictional force between the…

A:

Q: 2.5". 45 45°

A: Let’s divide the shaded area into two sections. Section 1 is a circular arc OCD and section 2 is a…

Q: What is the resultant force?

A: Let us consider that an object has two forces acts on it. These forces are  10 N to its right.  50…

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

A:

Q: Horizontal Component of the force at B: Vertical Component of the force at B: Horizontal Component…

A:

Q: Find (Ix&ly), if a=30mm. a

A:

Q: The design specifications for the steel shaft AB require that the shaft acquire a strain energy of…

A:

Q: data - The gas operating in the cycle is air. - The circulating air flow is 1 kg/s - The pressure…

A: Given data is

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Q: What is the direction of the edge formed between the intersection of (211) and (102)?

A:

Q: 5. The rectangular components of force are respectively. 220° 100 N (a) -100 sin 220°, –100 cos 220°…

A: As we know, there are four quadrants: I, II, III, IV. In the first quadrant, x and y-axis are…

Q: 12. Draw the SFD and BMD for Figure 7 on the axes provided. Be sure to label the coordinates for the…

A:

Q: Dotermine ali force truss Shown mem bers of thhe

A:

Q: Find the angle between the planes x + y = 1 and 2x + y -2z = 2

A: Write the expression to determine the normal vector of both the planes. Substitute the value of…

Q: 2. The size of 1/2 in. would refer to the with regard to ACR copper tubing.

A: The correct option is (b)  Outer Diameter (OD)

Q: x2(1) x1(t) K fv, M2 f(t) M1 fv, fv. fv,

A:

Q: Calculate the forces at a: F_Ax = ___________, F_Ay=__________________, and the forces at D: F_Dx =…

A:

Q: +y (i) +5 dx y cosx dx dy dx (m) dx (iv) dx

A: Degree & Order: Order: highest numbered derivative in the equation Degree: highest power to…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.