We are given the per unit model of a single phase power transformer with ratings 60 Hz, 25.0000000000 KVA, 12.0000000000kV/280.0000000000V, as follows: Rsc = 0.0450000000 p.u., Xsc = 0.2250000000 p.u., Rc = 190.0000000000 p.u., Xm = 63.3333333333 p.u. Those values were computed from a set of standard (as seen in class) open circuit test and short circuit test. Compute and report what were the OCT and SCT values measured originally. Voc = volts Iocamps Poc = Vsc = Isc = Psc = watts volts amps watts

We are given the per unit model of a single phase power transformer with ratings 60 Hz, 25.0000000000 KVA, 12.0000000000kV/280.0000000000V, as follows: Rsc = 0.0450000000 p.u., Xsc = 0.2250000000 p.u., Rc = 190.0000000000 p.u., Xm = 63.3333333333 p.u. Those values were computed from a set of standard (as seen in class) open circuit test and short circuit test. Compute and report what were the OCT and SCT values measured originally. Voc = volts Iocamps Poc = Vsc = Isc = Psc = watts volts amps watts

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4MCQ: An ideal transformer has no real or reactive power loss. (a) True (b) False

See similar textbooks

Similar questions

In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
Topic- basic & const.
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
eeff
I need the answer at 20 minute
An ideal transformer circuit is shown in Figure Q4(a). Its primary and secondary turns are 400 and 200 respectively. (1) Calculate the rms primary current. (ii) Calculate the rms flux in the transformer core. (iii) State two losses that contribute to transformer active power loss that have been ignored in this ideal model. N, Ny 30 + j30 2 300 sin50t Figure Q4(a) 00000000
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
The primary ofa certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
The full-load efficiency of transformer at 0.85 lagging p.f. is 97%. Its efficiency at full load 0.85 leading power factor will be *
SOLVE STEP BY STEP IN DIGITAL FORMAT XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 2. A transformer with a 10/1 turns ratio has a maximum flux density of 60,000 lines/in2, when the primary winding is connected to a 2300 V power supply at 60 cps. What will be the maximum flux density if the secondary is connected to a 115 volt supply at 25 cps with the primary open?