identical pumps each withdesign discharge ofwath is to be lifted bynet head of 200m,Specific speed of 4o and octational speed of 1400 opm with0.2 m³/sec are available. The minimum number of pumps required is

Given data, Discharge (Q) = 0.2 m³/s Specific speed (Ns) = 40 rpm Rotational speed (N) = 1400 rpm…

wath is to be lifted by net head of 200 a m, identical pumps each with specific speed of 4o and octational speed of 1400 opm with design discharge of 0.2 m³/sec are available. The minimum number of pumps required is

wath is to be lifted by net head of 200 a m, identical pumps each with specific speed of 4o and octational speed of 1400 opm with design discharge of 0.2 m³/sec are available. The minimum number of pumps required is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q/Suppose there are three identical pumps in series, each producing 1500 ft of the head at flow rate 1000 gpm capacity, and another case there are three pumps in series that have differing heads of 1500 ft, 1200 fi, and 1400 ft at 1000 gpm, Find the total head and flow rate generated and discuss the different if conneet parallel ?
Find the calculation flow rates of the rainwater channels given in the figure. i- AP/AT, F166.67 i (lt/s.ha) 3. ha=hectare A13(hectare) ta13(min) C13 A23 ta23 C23 A34 ta34 C34 (ha) (min) (ha) (min) 1.25 10 0.66 2 8 0,85 1,28 12 0,68 Tr(min) nh (mm) Th (min) nr 1,25 18 22 2,5 15
Using the pump selection table below to determine the best pump for the given condition: 20 Imp.g.p.m 100 • A flow of 0.01 m³ /s and a head of 25 m 20 US.g-p.m 200 s 0 100 100-80/32 100-65/32 300 65–40/32 80-50/32 100-80/26 125-100/26 12 5-40/265-50/26 80-65/26 100 50-32/25- 1-100/20 100-80/20 (ft) 5-50/2080-65/20 65-40/20 50-32/20 100-80/16 80-85/16 65-50/16 (m) s0-32/16- 65-40/16 80-65/13 S-0/13 65-50/13 40–32/13 20 2900r/min 14 14 nyh Q L/s 12 50 200 s0 * O 100 15 125-100/16 ..
The critical depth of flow (in m) for the parabolic channel as shown in the figure for a discharge of a 4 cumecs will be y 4 y = 2x
Pumps of specific speed 30, rotational velocity 1450 RPM, and discharge rate of 0.2 m3/s are installed to achieve a net head of 150 m. Determine the number of pumps required to get the net head of 150 m.
Estimate roughly the sizes of supply conduits leading to an 1. adequate service reservoir, serving (a) a relatively small town of 25,000 population. (b) a relatively large city with industrial establishments having a popu- lation of 5 lakh people. Also find the hydraulic gradients at which the pipe lines are proposed to be laid. Assume any suitable data according to Indian conditions, where required.
Problem 3 • The min and peak sewage flows are 2500 m3/day ,25000 m3/day with an Qava of 7500m3/day at the pumping station. Design the wet well if the pump has a min cycle time of 30 min. At what flow cycle time will be 2 times the min cycle time.
Q/ A small sewage pumping station with two identical pumps is to be selected for an average flow of 400 m/day. The minimum flow rate is one quarter the average and the maximum 150 percent of average. Determine the working volume required, the pump capacity, and the cycle time at maximum and average flow. The minimum cycle time is 5 min and the minimum running time 2 min.
Design and Selection of a Pump-Piping System A project requires a pump that will operate with a minimum discharge of 20 L/s against an elevation head of 40 m. The distance between the supply and delivery points is 150 m. A ball check valve will be used in the system that consists of commercial steel pipes. In order to produce a solution that meets the specified needs for the system design, it is required to determine the most economical pipe diameter for the pipeline and select a single pump from the figures below (including its operating conditions) if the total cost (in thousands of dollars) can be expressed as C = d175 + 0.75P + 18 where d is the pipe diameter (cm] and P is the pump power input [hp]. The followings are required to be conducted: 1. Describe clearly the mathematical model (equations/formulac) used to conduct the system design. 2. Design the pump-piping system (pipeline size, pump selection and total cost) using one of the modern engineering software. 3. Analyze and…
Answer fast
Please solve the following. This is hydraulics subject. Please always retain 3 decimal places upon calculation and in the final answer. Please put an appropriate units upon calculation and in the final answer. Put diagram if necessary. Problem: A dedicated pump station supplies 20 MLD of water to an executive subdivision. Determine the power requirement of the pump station if the working head is 55 m and the efficiency of the pump is 85%.
Three pumps are connected in series. According to pump performance curves, the free delivery of each pump is as follows: Pump 1: 1600 L/min, If the flow rate for this pump system is 2400 L/min, which pump(s) should be shut off? Pump 2: 2200 L/min, Pump 3: 2800 L/min