A double acting reciprocating pump having piston area 0.1m² has a stroke length 3 0.30m. The pump is discharging 2.4m of water per minute at 45 r.p.m. through a height of 10m. What is the slip of the pump?

A double acting reciprocating pump having piston area 0.1m² has a stroke length 3 0.30m. The pump is discharging 2.4m of water per minute at 45 r.p.m. through a height of 10m. What is the slip of the pump?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three pipes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for pipe A,L= 1800 m, diameter= 0.90 m f= 0.012; for pipe B, L= 1500 m, diameter= 0.60 m f=0.012 and for pipe C, L= 800 m , diameter = 0.45 m, f= 0.012. Disregarding minor losses, find the total headloss of the pipe. a. 0.492 m. b. 0.078 m. c. 1.15 m. d. 1.675 m.
Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine the the required pumping power input for flow over a 200-feet long section of the pipe. A 530 Watts В 461 Watts C) 315 Watts D) None of the above
A centrifugal pump having outer diameter equal to two times the inner diameter and running at 1000 rpm. Works against a total head of 40 m. The velocity of flow through the impeller is constant and equal to 2.5 m/s. The vanes are set back at an angle 40° at outlet. If the outer diameter of the impeller is 500 mm and width at outlet is 50 mm, the discharge is. (a) 1.963 m³/sec (b) 0.1963m ^3 (c) 0.1963 m³/sec (d) 0.1963 cm³/sec
ANSWER ASAP. WILL UPVOTE
630 cm^3/s Water at 320 k is PumPed in a 40 mm (id) through a length of 150m in horizontal direction and up through avertical height of 10m. in the Pipe there is a control Valve which may be taken as equivelent to 200 Pipe diameter and also there is other Pipe fitting equivalent to 60d. if the main Pipe has a roughness of 0.0002m. what a power of PumP if It's efficiency is 60% And the viscosity is 0.00065 pa.s
Water flows in a l-in-diameter pipe at 10 ft/s. If a pitot-static tube of 0.5-in diameter is inserted, what velocity will be indicated? Assume one- dimensional frictionless flow. Find the pitot-static-tube diameter needed reduce the above error to 1 percent.
A centrifugal pump having a head-capacity relationship given by the pump curve equation h₂ = 180 - 6.10 × 104 Q², with ha in feet when Q is in gpm, is to be used with the system shown in the figure. For Z2 - Z₁ = 50 ft, what is the expected flowrate if the total length of constant diameter pipe is 600 ft and the fluid is water? Assume the pipe diameter to be 4 in. and the friction factor to be equal to 0.02. Neglect all minor losses. (2) (1) Pump 22
Problem 7- 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir Cif the inflow to reservoir A is 515 Lit/sec. El. ? C El. 90 m El, 90 m B D. 300m - 450 mm t=0.03 El. 80 m 600m - 600 mm f-0.025 300m- 450 mem f0.03 900m- 450 mm 8. 600m - 450 mm 0.03
A flocculation tank is to be designed for a total flow rate of 45000 m3/d. The following conditions apply to the design: Water temperature 15 C (viscosity =0.00113 N.s/m2) Basin depth 3.8 m, 4 parallel trains of flocculators (each train receives quarter of the total flow). Each train with 9.2m wide, 12.4 long, and rotating paddles are supported on three parallel horizontal shafts. The rotating speed is 1.6 rpm, the center line of the paddles is 1.5 m from shaft. Each shaft has four paddles, each paddle is 25 cm wide and 8.6 m long. Assuming the velocity of water is 35% of the paddle's velocity and the drag coefficient Determine: 1.9. The difference in velocity between paddle and water? The useful power input? The detention time? The value of G and Gt?
T1. Water is to be pumped from a reservoir at datum level 6.5m to a reservoir at datum level 24.8m at the rate of 55.6 l/s by a pump at datum level 9.2m. The suction pipe is 21m of 200mm diameter, and the delivery pipe is 186m of 100mm diameter, both with friction factor 0.015. What head must be generated by the pump. Answer 89.9m Delivery reservoir ha Z₂ hs Suction reservoir Datum Z₁ Pump
6. A pump is connected to a rising main with a diameter of 0.35m and length of 400m. The rising main discharges to a level 32m above the sump level. The friction factor of the rising main may be taken as 0.01, local losses total 2.5V² /2g, and the pump has the characteristics shown in Table Q6. Determine the flow rate, head and efficiency at duty point under the following design scenarios: () One pump (i) Two pumps operating in parallel (ii) Two pumps operating in series You may find the following expression useful: ALV? h, 2gD Table 6: Pump A characteristics Flow rate (m3/s) 0 0.1 0.2 0.3 0.4 0.5 Pump head (m) 39 38 35 30 22 12 Efficiency (%) 48 62 63 55 44
A pelton uheel has a mean bucket speed of 10 m/sec with a jet of water flowing at the rate of 0.7 m3/sec under a head of 30 m. The bucket deflect the jet through an angle of 160°. Calculate power given by water to the runner and the hydraulic efficiency of the turbine. Assume efficiency of the nozzle as 0.98.