Answered: WATER IS TO FLOW AT THE RATE OF 25 m³…

WATER IS TO FLOW AT THE RATE OF 25 m³ /s IN THE CONCRETE CHANNEL AS SHOWN. FIND THE 1.5 m REQUIRED VERTICAL DROP OF THE 3.5m CHANNEL BOTTOM PER 2 m KILOMETER LENGTH. USE n = 0.013.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A trapezoidal channel with a bottom width of 5 and slide slopes having a ratio of 3H:1V, conveys water at 19 m3/s. If n = 0.012, what is the critical depth? Answer is 0.936
5.5. A power-law channel section is to be excavated to accommodate 15 m³/s when flowing full. The channel is on a slope of 0.07%, and Manning's n of the lining material is estimated as 0.015. If the channel is to have a top width of 1.50 m, what is the equation of the shape of the best hydraulic section?
complete solution. need ASAP. THANK YOU
PART III. PROBLEM SOLVING 1. The figure shows a weir, the base of which is 6m below the ground. The necessary flow net has also been drawn assuming K, = K, = K. K = 0.005 m/sec. Compute the following: a. rate of seepage through the foundation in liters/sec. b. uplift pressure at "f. weir uplift force per unit length measured along the axis of the weir. c. 2. For the stressed soil element shown: a. Compute the major principal stress b. Compute the minor principal stress c. Compute the normal stress on plane DE O150 kPa 10 Ty50 LPa
A trapezoidal channel has a base of 1.5 m and 45-degree walls. A smooth asphalt lining (n = 0.015) is used and the channel slopes at 2.5%. If the water speed is measured at 7.5 m3/s, what is the water depth in the channel?
2. From the flownet in the figure, estimate (a) the flow rate beneath the dam (b) the maximum exit gradient. (c) the water pressure at the tip of each cut-off wall (d) the uplift force on the base of the structure (Ans: a) Q = 3.47 × 10-8 m³/s/m; b) ie = 0.35; c) pL = 107.6 kPa, PR = 92.9 kPa; d) U≈ 670 kN/m) 20 5 20 dimensions in meters k=10-8 m/s
A concrete channel which is laid on a slope of 1.9m per kilometer discharges water at a rate of 3 m3 /s. Using a roughness coefficient, n = 0.014, determine the depth (d) of water for the most efficient sections: a. triangular b. rectangular c. trapezoidal
Water flows at flow rate Q In a rectangular canal. At height [m] 2 = h. And in width. b = 4 [m]. Manning's coefficient of roughness in the canal is. 0.015 = n Shear stress measured in channel tau = 9.81 In / m2). Next to the canal, a vertical partition was installed that divided the canal into two identical canals, the width of each canal being [m] 2 = 2/ b. A. Calculate the water level in each separate rectangular channel h h= ? b-4m B. The cross section changed to one connected rectangular channel as it was at the beginning when the water height is h = 2 [m] and width b = 4m. Add a step to the rectangular channel to create a control section (critical flow). Calculate the step height (delta (z) in the control section h=2m Az-!
Design a trapezoidal open channel (n=0.014) that is anticipated to convey 20cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic radius of the designed section.
A concrete gravity dam has the following data: Maximum water level = 300.00 m Bed level = 220.00 m R.L top of dam = 304.00 m %3D The d/s slope of 0.67:1 starts at RL of 295.00 m U/s face is vertical. Center line of the drainage gallery = 8.0 m from u/s face. Consider only weight of dam, water pressure and uplift pressure. Calculate only the normal stresses at the toe and heel of the dam, assuming 100% uplift pressure at the h eel and 50% at the gallery and zero at the toe.
For the 2D duct below, determine the stream function using 4x = 4y = 0.1 m. 3 m 2 m/s ► ► → 5 m 2m 1m
Design a semi-circular open channel (n=0.014) that is anticipated to convey 25cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic depth of the designed section.