Water is stored in a pressurised container at a height HT = 8 m. It then moves through a horizontal pipe which has a height Hp = 0.6 m off the ground. A fault occurs, and the water in the pipe is ejected vertically out of a valve, as shown in the figure. The jet reaches a maximum height H; off the ground. The density of water is p = 1000 kg/m³, and the gauge pressure in the tank is pt = 30 kPa.

Water is stored in a pressurised container at a height HT = 8 m. It then moves through a horizontal pipe which has a height Hp = 0.6 m off the ground. A fault occurs, and the water in the pipe is ejected vertically out of a valve, as shown in the figure. The jet reaches a maximum height H; off the ground. The density of water is p = 1000 kg/m³, and the gauge pressure in the tank is pt = 30 kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given parameters D1=30 cm L1=300 m D2=20 cm L2=150 m D3=25 cm L3=200 m f1=0.018, f2=0.02, and f3=0.019, determine the flow rate between reservoirs A and B, which are connected to each other as shown in the diagram. Note that the sudden contraction loss coefficient k is assumed to be 0.24.
I2
According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
The cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.1 m at the bottom of the tank. What is the time required for half of the water in the tank to drain after the outlet line is opened? The flow velocity of water from the bottom of the water tank is related to the height of the water in the tank, and this relationship is expressed by the formula v: (m / sec) linear flow velocity, g: gravitational acceleration (10 m / sec2) and h: (m) height.
The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. May you kindly resend the answers in a different format as they appear blank??
What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to H=7.0 m? D=20 cm – H water d1= 4cm d2=3 cm v2=2 m/s v1=5 m/s
Q2: Water flow in a pipe as shown in the figure if the velocity of the fluid at section A is 1.8 m/s and at section D 1.36 m/s. Find A 1. pressure drop at section C d-300 mm d-400 mm 2. head losses at section D Take the density of water 1000 kg/m³ and viscosity of water 998 × 10-6 N.s/m² B 5 m- d-150 mm d-125 mm D
Let the pressure gradient in the pipe be 1500 Pa/m and the diameter of the pipe be 4.0 mm. What is the average speed through this pipe of 20∘C motor oil? What is the average speed through this pipe of 100∘C motor oil?
Q6
The device shown in the fugure below is known as a venturi. In theis specific venturi the differential pressure between locations 1 and 2 is 5 psi and the diameter ratio is D2/D1 =0.35 if D2= 8inches find the air flow rate through the frictionless venturi
13 Pun & 2.5m Tank A E 6 m 13m V= 0.8 m/s Tank P : 1o kpa 1Scm Exercise#1 In the shown figure, it is a system which its energy is assumed to be conservative. Tank B is open to the air and the tank A is closed at point 1. If the control valve after the tank A is opened fully (100%) and you know that 0 60°, what will be the reading of the flow meter at point 2 ?(Note: y = 5.8 kN / m3)