Water is released from a sluice gate in a rectangular channel 5ft with such that the depth is 2 ft and the velocity is 15 fps. 1. Find the critical depth for this specific energy.  a. 5.946 ft b. 3.036 ft c. 5.516 ft d. 4.926 ft 2. Find the critical depth for this rate of discharge.  a. 5.94 ft b. 3.03 ft c. 3.66 ft d. 4.92 ft

Q: Fluid Mechanics Question

A:

Q: Q-Water is flowing a critical depth at a section in a A shaped channel with side lopes of 0.5 H:1V.…

A: A V-shaped channel. Side slope = 0.5H:1V Critical depth = 1.6 m To determine The discharge, Q at…

Q: A reservoir has a sidewall, inclined backwards 30deg from the vertical in which is an orifice having…

A: Head available at orifice, H = 3 m Velocity coefficient, Cv = 0.97   The velocity of jet at the…

Q: Q- An orifice is located in the side of a tank with its centre 10 cm above the base of the tank. The…

A: Given- Height of orifice h=10 cm=0.10 m, Water level height H=1 m, Coefficient of velocity C=0.98,…

Q: Water flows from the faucet on the second floor of the building shown in Fig, with a maximum…

A:

Q: A swimming pool with vertical sides is 25m king and 10m wide. Water at the feel and shallow ends is…

A: Step 1: To solve these problems, we'll need to apply principles of fluid dynamics and use relevant…

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

A:

Q: Water flows out of the horizontal pipes at A and B. Water flows into the Tee at 10 m/s and under a…

A:

Q: --1. For supplying water to a colony, it is intended to store water in a Targe tank, whose water…

A:

Q: O1 A rectangular channel 2.5 m wide has a specific energy of 1.5 m when carrying a discharge of 6.48…

A: To find the alternate depth and critical specific energy-

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. acceleration due to…

A:

Q: Q-Water is flowing a critical depth at a section in a A shaped channel with side lopes of 0.5 H:1V.…

A:

Q: For the opened channel find the discharge if (S= 1/200) and (n=0.015).

A:

Q: Q-Water is flowing a critical depth at a section in a A shaped channel with side lopes of 0.5 H:1V.…

A: Given: Side slope = ( mH : 1V) = (0.5H:1V) Critical depth, yc= 1.6 m  Required: Discharge in channel…

Q: 10kN 10kN/m (10KN-m B - 3 m- -6 m- Determine the resultant of the system and its position from point…

A:

Q: Q-Water is flowing a critical depth at a section in a A shaped channel with side lopes of 0.5 H:1V.…

A: To find discharge and specific energy

Q: Water from a deep reservoir is collected with help from a pump. The discharge at B measures at 0.94…

A:

Q: A channel of rectangular section, 9ft wide, is discharging water at a rate of 71034gal/min with an…

A: "Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at…

Q: Water (25°C) is being supplied from a pump station to a reservoir tank through a horizontally-placed…

A:

Q: Elev, 110' 15 Inv. 102.5 Elev. 127.6 623.5 -1000' 2000' B Inv. 85 Assuming the conduit in the figure…

A: Wrought iron pipe dia =36''f=0.008 for wrought iron

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

A:

Q: Q-Water is flowing a critical depth at a section in a A shaped channel with side lopes of 0.5 H:1V.…

A:

Q: 5. The maximum velocity in a circular pipe when flow is laminar occurs at C. the bottom of the pipe…

A:

Q: Q- An orifice is located in the side of a tank with its centre 10 cm above the base of the tank. The…

A:

Q: Waters enter a pump through a 25 cm. dia. Pipe at 35Kpa. It leaves the pump at 140 kPa through a 15…

A:

Q: A 1000-ft-long 2-ft-diameter concrete pipe (sharp-edge entrance) is used to convey 60°F water from…

A:

Q: i's skundalini y² = 20 2y²y² (Y₁+ y₂)' If y₁ and y₂ are alternate depth in a rectangular channel…

A:

Q: Describe the following types of traffic volume counts and explain when they are used: 1. Control…

A:

Q: Q3. The system shown consists of 800 m long pipe of 5 cm cast-iron pipe connected into 400m long…

A: L1 = 800 m D1 = 5 cm or 0.05 m L2 = 400 m  D2 = 7 cm or 0.07 m  Q = 0.005 m3/s

Q: The critical depth at a section of a rectangular channel is 1.5m. The specific energy at that…

A: THE SPECIFIC ENERGY OF THE SECTION IS 2.25 m Answer is option C

Q: Q-Water is flowing a critical depth at a section in a A shaped channel with side lopes of 0.5 H:1V.…

A:

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

A: Given data: A rectangular open channel width, B = 6 m Discharge, Q = 20 m3/s Acceleration due to…

Q: A channel of rectangular section, 9ft wide, is discharging water at a rate of 71034gal/min with an…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Water is pumped from a tank, point (1), to the top of a water plant aerator, point (2), as shown in…

A:

Q: 5. The maximum velocity in a circular pipe when flow is laminar occurs at C. the bottom of the pipe…

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.