Water is pumped at a steady uniform flow rate of 0.01 m³/s through a horizontal smooth circular pipe of 100 mm diameter. Given that the Reynolds number is 800 and g is 9.81 m/s², the head loss (in meters, up to one decimal place) per km length due to friction would be

Water is pumped at a steady uniform flow rate of 0.01 m³/s through a horizontal smooth circular pipe of 100 mm diameter. Given that the Reynolds number is 800 and g is 9.81 m/s², the head loss (in meters, up to one decimal place) per km length due to friction would be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from A to B is 8 cfs, Determine the head loss in feet in PIPE 5. *23.8062*9.0254*1.0666*2.6570 Determine the flow in the upper branch pipe Q2 in cubic feet per second. *2.6667*2.3809*4.8840*12.4747 Determine the head loss in feet in PIPE 2. *3.4373*8.0165*9.2849*10.4720 Determine the total head loss in feet between the inlet A and the outlet D. *9.2849*13.1625*17.3474*35.9163
3 .Consider the incompressible flow of an ideal fluid having a density ρ = 1600 kg / m3 (figure 3). We give: P1 = 2 105Pa, P2 = 3 105Pa, V2 = 1 m / s and V1 = 0.5m / s. Determine the net power of the pump to ensure a volume flow Qv = 0.01 m3 / s.
Que. 5.6 A centrifugal pump having an impeller of 35 cm outside diameter rotates at 1000 rpm. The vanes are radial at exit and are 7 cm wide. The velocity of radial flow through the impeller is 3 m / sec. The velocity in the suction and delivery pipes are 2.5 m/s and 1.5 m / s respectively. Neglecting frictional losses determine the height through which pump lifts the water and the horse 3 - power the pump
A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet. Assume C = 0.63. The tank is filled with 7000 liters of water. What is the depth of the water in the tank in meters? How long will it take to drain the content of the tank in minutes? show solution and diagram
Please solve #4 &5 Thankyou
What is the head that must be supplied by the pump to the water to pump 0.4 m³/s from the lower to the upper reservoir ? Hint: [The head loss in the pipes is given in the figure as a function of water velocity]. Elevation = 150m Water Elevation 100m h₁=45v²/2g d=15cm Water Pump h=22.5v²12g d=20cm Elevation 40m
A 1.5m square tank, 3m tall is drained by a 25mm-diameter orifice located at its bottom. If the tank is initially filled with water, how deep is the water in the tank after 45 minutes? Assume C=0.62
Three reservoirs A, B and C are connected by a pipe system shown in the figure below. If the rate of flow from the reservoir A is 55 l's, and the coefficient of friction (F) for all pipes is 0.015. Find the piezometric head at point D A L2=600 m d2=20 cm D Q1=0.055 m/s L1=1200 m d1=30 cm 28 m 30 m
Calculate the hydraulic power of a pump (kW) that transfers water at 300 m3/hr to a tank at an elevation of 11 m. The suction side has pressure and velocity of 120 kPa and 1.5 m/s, respectively; the discharge side is 260 kPa and 3.2 m/s. Let γwater=9.81 kN/m3, g=9.81 m/s2 Round off your answer to four (4) decimal places.
A pump is used to move water from a lake to a large industrial tank, which is 30 m higher than the reservoir surface through a pipe 300 m long at a flow rate of 1 m³/s. The pipes are uniform and having a diameter of 60 cm. The friction factor in the pipe is given as f = 0.05. The vapour pressure of water can be taken as 4780 kPa. Calculate (a) Velocity of water through the pipe (b) Head loss in the pipe (c) Required head by the pump (d) Power supplied, in kW if pump efficiency is 75% (e) Available NPSH for the pump installation
Water (p =1000 kg/m , p=1.59×103 kg /m.s) is flowing with the velocity of 0.25 m/s through a smooth pipe with the diameter of 1 cm at 25 °C. i. Calculate the head loss in 1 m of the pipe. ii. Calculate the head loss if the water velocity increases to 1 m/s.
Imagine that the water level in Problem 8.34 rises at a rate of 0.1 cm/s. Knowing the diameter of the tank is 15 cm, what is the average velocity of the water leaving the tank?