Water is moving between two reservoirs at a flow rate of 0.08 m³/s via the pipes shown in the diagram (D₁ = 10 cm, D2 = 20 cm). Assume both pipes have a roughness ks = 0.08 mm. If the difference in water surface elevation between the two reservoirs is 70 m and L₁ = 50 m, what is the length of the larger pipe (L2)? Further, what is the entrance length of pipe 1? For what fraction of the length of pipe 1 is flow fully developed? Include form losses due to pipe components (entrance, expansion, and exit) in your calculations. For more info on component losses, use Table 10.5 and 0 = 180°. Water T = 20°C D₁ 4₁-4 D₂ 42

Water is moving between two reservoirs at a flow rate of 0.08 m³/s via the pipes shown in the diagram (D₁ = 10 cm, D2 = 20 cm). Assume both pipes have a roughness ks = 0.08 mm. If the difference in water surface elevation between the two reservoirs is 70 m and L₁ = 50 m, what is the length of the larger pipe (L2)? Further, what is the entrance length of pipe 1? For what fraction of the length of pipe 1 is flow fully developed? Include form losses due to pipe components (entrance, expansion, and exit) in your calculations. For more info on component losses, use Table 10.5 and 0 = 180°. Water T = 20°C D₁ 4₁-4 D₂ 42

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Asaap
Calculate the daily flow in (m³/d) using Darcy's law for a confined aquifer with a hydraulic conductivity of 1.9 (m/d), a thickness of 50 (m) which is 5 (km) wide. Two observation wells are located 1.8 (km) apart in the direction of flow and the head in well 1 is 105 (m) and in well 2 is 95 (m). (Please enter your answer with one decimal)
A horizontal water pipeline 50-cm diameter carries a discharge of 0.5 m/s at a pressure of 55 kN/m?. It then reduces to 300-mm diameter. For the 300-mm pipe, calculate the (a) velocity (m/s) and (b) pressure head (m).
Thank you professor !!
Question 2: A pipeline carries a pumped flow of 0.05 m/s. The line contains three 90 degree bends (K=0.9), a gate valve (K=0.4), and a swing check valve (K=0.6). Select an internal diameter between 10 cm to 90 cm for steel pipe (e= 0.00015 in, 0.00381 mm). Determine the total head loss if the lengt of the straight pipe is 300 m.
For the pipe networks shown, the flow of water from reservoir A to the junction is 0.035 cu.m.per second. a) Determine Q2, Q3 b) Determine the head loss from A to B
o T ☺ ť Water is flowing in a compound open channel as shown in Figure. Given the channel bed slope as 0.0016 and Manning's n = 0.03, nz = 0.025 and ns = 0.03. calculate the flow rate using equivalent Manning's n method. Determine the equivalent n: i. ii. Determine the flow rate. 0.8 m 1.8 m 1.4 m 1.2 0.6 m مرّ للأعلى لاستعراض الفلاتر إضافة شرح. .. mum <
Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the head loss through the network. Pipe 1: D₁ = 450mm, L₁ = 800m Pipe 2: D₂ = 400mm, L₂ = 700m Pipe 3: D3 = 500mm, L₁ = 600m 15.2m O 24.4m O 28.3m O 22.2m
Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the volumetric flowrate in Pipe 1. Pipe 1: D₁ = 450mm, L₁ = 800m 1 Pipe 2: D₂ = 400mm, L₂ = 700m L2 Pipe 3: D3 = 500mm, L₁ = 600m O 0.69m^3/s O 0.78m^3/s O 0.46m^3/s O 0.63m^3/s
2. Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Pipe 1: L = 5000 m, D = 300 mm Pipe 2: L = 4000 m, D = 250 mm Pipe 3: L = 3500 m %3D The flow from reservoir A to junction P is 0.045 m3/s and f for all pipes is 0.018. (a) Find the elevation of the energy grade line at P in m (b) Determine the flow on pipe 2 in m3/s (c) Compute the diameter appropriate for pipe 3 in mm
Three reservoirs A, B, and C are connected by pipeline 1, 2 and 3 respectively which merges at a junction X. The elevation of reservoir A is 350 m and that of B is 290m. The rate of flow from A is 1.5 m^3/s. (See the table) 1. Compute the rate of flow in reservoirs B and C. Pipes Diameter Length Friction factor “f” 1 825 mm 1500 m 0.0155 2 650 mm 450 m 0.0165 3 450 mm 1200 m 0.0175
M - Problem 3: For these three reservoirs please assume that the elevations of the waterlines in reservoirs 1-3 are: h, 30 m, h₂-20 m, and h, 10 m. Also, please assume that the lengths of pipes 1-3 are L₁ 1000 m, L₂ 2000 m, and L3 = 3000 m; the diameters of all three pipes are D₁ D₂ D₂ = 2.0 m; and the friction coefficients of all three pipes are f f₂=fa=0.015. If you estimate that the total head at Junction "J" is H, = 22 m please: 1) calculate the resulting net volumetric flow rate into junction "J" and 2) determine if the actual total head at junction "J" is above or below H, = 22 m. h₂ Reservoir 1 h₂ 7 Reservoir 2 Pipe D Reservoir 3 ha Pipe 3 Pipe 2 a