Water is flowing with flow rate 28 liter/s in a 100 mm diameter concrete lining centrifugally spun pipe as shown in the figure. The pipe length between the pressure gauges is 180 m. Determine the pressure gauge reading by using the Darcy Weisbach formula with loss coefficient method and Darcy Weisbach formula with effective length method.

Q: Calculate the settling velocity of the sandy materials present in the wastewater inside the grit…

A:

Q: Problem 3 The figure presents the portion of the pipe network through which a fluid with a specific…

A:

Q: Air (1.23 kg/m³) flows past an object in a 2-m-diameter pipe and exits as a free jet as shown in the…

A: Given, ρ = 1.23 kg/m3 D = 2 m   NOTE : As per guidelines, first 3 parts are solved. Request you to…

Q: me discharge (Q)through a horizontal pipe is depend upon the pressure drop per unit length the…

A:

Q: ion 1: The absolute pressure in a gas tank is 300 kPa. Determine the gage pressure

A: Given data : The value of absolute pressure=PAbs PAbs=300 KPa The value of atmospheric pressure…

Q: Calculate the water speed in ft/s at point (cross-section) (2). V₂ = eTextbook and Media Save for…

A:

Q: ASAP. Please answer the question properly with a complete solution. A non-rigid steel pipe 70 cm in…

A:

Q: Water flows from reservoir A to B through the three concrete pipes shown below. Assume that concrete…

A: GivenH=20mL1=2500md1=400mm or D1=0.4mL2=1850m, d2=300mm or D2=0.3mL3=800m, d3=200mm or…

Q: x 75 mm venture meter is inserted in a 300 mm diameter main pipe where water flows at 55 L/s.…

A:

Q: PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at…

A: step 1-

Q: Question 16 The pipe diameter is 800mm. The ultrasonic measurements recorded are: • Pipe centerline…

A:

Q: Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the…

A:

Q: Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large open…

A: Given, Q = 45 ft3/min or 0.75 cfs D = 2.5 in or 0.208 ft

Q: Calculate the pressure difference between the 2 points shown on the figure below (P1 - P2)? Fluid in…

A: Given :-       The pressure difference between 2 points ( P1-P2)           SG =13.6           Cross-…

Q: A circular, downward water jet impacts a horizontal plate as shown in the figure below. The exit…

A: A vertical downward jet flow from the pipe impacts a plate kept at a certain distance. The velocity,…

Q: From section 1 at p₁-750 kPa, water flows through a galvanized iron pipe of 50 mm inside diameter…

A: Given, P1 = 750 kPa  D = 50 mm L = 40 m  Q = 0.015 m3/s

Q: Compute the pressure at point B

A:

Q: A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the…

A:

Q: A 6 in diameter new, unlined ductile iron pipe carries a flow of 150 usgpm and is O.2 miles long.…

A:

Q: A water pipe gradually changes from 150 mm at a point X to 450 mm at point Y. Point X is 5 m below…

A:

Q: The discharge (Q) through a horizontal pipe is depend upon the pressure drop per unit length(AP) the…

A:

Q: A 11 inches pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the…

A: Differential gauge: The device used to evaluate the difference between two points having different…

Q: A valve is suddenly closed in a 200 mmø pipe. The increase in pressure is 700 kPa. Assuming that the…

A: compute the water hammer pressure in kPa at the valve if it is closed in 3 sec.

Q: An ideal fluid with y = 8825 N/m flows in the vertical circular pipe represented below. The flow…

A:

Q: 1. A differential manometer is attached to a pipe as shown. Calculate the pressure difference…

A:

Q: In a pipeline with a diameter of 500mm, a venturi meter is installed. The ratio of the throat pipe…

A:

Q: This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The…

A:

Q: 2. The pipe shown in the figure has oil flowing with spgr of 0.82. If the total head loss from point…

A:

Q: Compute the Reynolds number for the flow of 895 L/min of water at 10°C in a standard hydraulic steel…

A: Q1 = 895l/min  Q2 = 46l/min

Q: A cylinder has a longitudinal joint that has a strength of 450kN per meter and the girth is 200kN/m…

A: Given : Strength of longitudinal joint = 450 kN/m                           Girth strength = 200…

Q: please give exact solution A pipe with a diameter of d is used to transport an incompressible fluid.…

A: Reynolds Number  Re=Inertial forcesViscous forces =ρVavgdμ we do not have any of these data to…

Q: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The…

A:

Q: I. Solve the given truss 69 in k 69 in k 10 9 ft 30 12 ft 12 ft 12 ft A. SOLVE MEMBERS EC, ED AND CD…

A:

Q: 3. From d figure below, if the atmos. pressure is 770mm of Hg, fınd: a) Rm if the pressure at B is…

A:

Q: Compute the pressure @ point n ( Pn ) as shown by the differential manometer in KPa if pressure @…

A: We know1mm hg=0.133322kpaso,Pm=1027.66 mm hg=137.01kpaso,Writing pressure…

Q: SUBJECT IS HYDRAULICS SHOW DETAILED AND COMPLETE SOLUTION USED 3 DECIMALS FOR THE FINAL ANSWER The…

A: Given

Q: Flowrate of water through bend pipe (90°) is 0.21 m3/s. The pipe diameter at the inlet is 150 mm and…

A: The discharge is Q=0.21 m3/s. Consider the following figure. Calculate the velocity at the inlet as…

Q: Oil h 0.2 m 0.3 m Water TB

A: Given data Specific gravity of oil = 0.9 Pressure difference between A and B , PA-PB = -5 kPa =-5 x…

Q: In the figure, friction loss between A and B is neglected while between B and C it is 0.2 (VB²/2g).…

A: Given, In figure, The diameter of pipes A&C = 443mm =0.443m Diameter of pipe B= 131mm= 0.131m…

Q: gure AG E 400 mm < 1 of 1

A:

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.