Water is flowing through a large circular conduit with inside radius R and a velocity profile given by the equation: v(fps) = 8 [1- (r/R)2]. Determine the mass flow rate through the pipe and the average water velocity in the 2.0 ft pipe.

Water is flowing through a large circular conduit with inside radius R and a velocity profile given by the equation: v(fps) = 8 [1- (r/R)2]. Determine the mass flow rate through the pipe and the average water velocity in the 2.0 ft pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B3
Water vapor at 400 temperature and 3 mpa pressure enters an adiabatic nozzle at a speed of 40 m/s and exits at a pressure of 2.5 mpa and a speed of 300 m/s. according to this a) find the outlet temperature B)Find the cross-sectional area ratio of the input and output ends (A1/A2)
C2. A circular pipe 1 of 535 mm diameter branches into two pipes (pipe 2 and pipe 3) of diameters 325 mm and 180 mm respectively as shown in figure below. If the average velocity of pipe 1 and pipe 3 are 4.7 m/s and 3.85 m/s and the flow rate of pipe 2 is 1/3rd water flow in pipe 1. D2 Pipe 2 Pipe -D, Find the following: (3 Marks) O Flow rate of water through pipe 1 in m/s (m Velocity (V)) of pipe 2 in m/s (iin) Flow rate of water (Q3) through pipe 3 in m/s
Need detailed solution. 4 decimal places. A fluid is flowing in a 6 in diameter pipe at a pressure of 4 psi with a velocity of 8 ft/s. The elevation of the center of the pipe above a given datum is 10 ft. Find the total energy head above the given datum in meters if the fluid is (a) water, (b) oil with specific gravity of 0.85, (c) gas with specific weight of 0.42 lb/ft^3
Please solve and answer the question correctly. Thank you!!
The following figure shows a bent in a pipe with a diameter of D (cm). Pressure is measured in cross section#1 as demonstrated in the figure as P1 (kPa). In cross section#2 the diameter reduced through a nozzle to 5.0 cm and the water is discharged into atmosphere. The elevation difference between two cross sections is 0.5 m. Assume all losses are negligible and density of the fluid, water, is 1000 kg/m³. a) Find the velocity in cross section#1; b) Calculate the horizontal and vertical forced acting on the pipe and the direction of the resultant force. D = 20 cm, Pj= 450 kPa Cross section#2 0.5 m Diameter: 5 cm P1 60° Cross section#1 Diameter: D cm
Please answer in accurate solution
Consider the mechanical energy equation: P + VB? + gzB =PA + V? + g ZA + w – loss A +g ZA + W – loss where loss 2 0 Select ALL true statements below. a fluid particle will flow through point A before point B a fluid particle will flow through point B before point A points A and B do not lie on the same streamline if a turbine is present, w < 0 if a pump is present, w < 0 if the fluid is perfectly inviscid, loss can be 0
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
find Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion A 30 cm diameter pipe, conveying water, branches into two pipes of diameters20 cm and 15 cmrespectively. If the average velocity in the 30 cm diameter pipe is 2.5 m/s, find the discharge inthis pipe (m3/s). Also determine the velocity (m/s) in 15 cm pipe if the average velocity in 20cm diameter pipe is 2 m/s.
The pressure differential of oil (with specific gravity of 0.789) flowing through different sections of pipe is 750 Pascals. If the velocity of the oil in the first pipeline section is 1.2 meters per second what is the velocity of this oil in the second pipeline section?
USE 4 DECIMAL PLACES ON YOUR FINALANSWERS DO NOTUSE SCIENTIFIC NOTATIONS NO NEED TO INPUT THE UNITS A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velacity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.