Water is flowing in a tube "D = 3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a uniform heat flux on the outer surface of the tube by electric resistance heater. If the Power rating is 16kW and the convective heat transfer coefficient is 757 W/m².K, what is the surface temperature at the exit "°C"? 660 3 Properties : p = 992.1 kg/m , C = 4179 J/kg.°C, k =,0.631 W/m°C, Pr=4.32, v = 0.658E-6 m /s %3D Select one: А. 84.68 B. 99.03 C. 91.85

Water is flowing in a tube "D = 3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a uniform heat flux on the outer surface of the tube by electric resistance heater. If the Power rating is 16kW and the convective heat transfer coefficient is 757 W/m².K, what is the surface temperature at the exit "°C"? 660 3 Properties : p = 992.1 kg/m , C = 4179 J/kg.°C, k =,0.631 W/m°C, Pr=4.32, v = 0.658E-6 m /s %3D Select one: А. 84.68 B. 99.03 C. 91.85

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Centre punch is a marking tool used in workshops for the purpose of making indentations on the workpiece with an included point angle of 900. Select one: True O False
where does the 64 come from?
What size hole was drilled in part? Would it be 3/16?
What is the counterclockwise angle?
n the surface roughness standard drawing shown below, the maximum waviness height is: O a. On top of the horizontal line to the right side O b. On top of the open triangle O c. Inside the shape next to the lay direction O d. On top of the horizontal line to the left side
Can I get the Top, Side and views. Using free-hand drawing of this coupling pieces..
Differentiate enery and force
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"
Question 3 The Extrude Cut feature in SOLIDWORKS can be used to create both through holes (holes that go all the way through a part) and counter bore holes (holes that do not go all the way through a part), such as the holes shown in the 2-dimensional image below. True False Counterbore
Which statement is correct?
17-5B pencil is lighter than 5H pencil. O True O False 8- This figure shows center line. O True OFalse 16- The orthogonal projections of this figure 16-The orthogonal projections of this figure are: O True O False ارسال الاجابة ارسال الاجابة ارسال الاجابة
Select all the correct statements: a. Moment of force or toque is force multiplied by the perpendicular distance from the point of application of the force to the selected point or center. b. The perpendicular distance is also termed as moment arm. C. The axis of the moments and the planes of the forces are intersecting at the center of the moment. d. Graphically, the moment can also be defined as the area of the triangle formed by joining the center of moments with the ends of the forces. B