Water is flowing from a garden hose. A child places his thumb to cover most of the hose outlet, causing a thin jet of high-speed water to emerge. The pressure in the hose just upstream of his thumb is P1-Patm=50 kPa (gauge). If the hose is held upward, determine the maximum height that the jet could achieve (h= ? m). Pwater=1000 kg/m3, v12<

Water is flowing from a garden hose. A child places his thumb to cover most of the hose outlet, causing a thin jet of high-speed water to emerge. The pressure in the hose just upstream of his thumb is P1-Patm=50 kPa (gauge). If the hose is held upward, determine the maximum height that the jet could achieve (h= ? m). Pwater=1000 kg/m3, v12<

Name: Water is flowing from a garden hose. A child places his thumb to cove
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Water is flowing from a garden hose. A child places his thumb to cover most of the hose outlet, causing a thin jet of high-speed water to emerge. The pressure inthe hose just upstream of his thumb is P1-Patm=50 kPa (gauge). If the hose is held upwar

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Subject :Fluid mechanics Give me right solution. Help me urgent
Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady, incompressible, irrational with negligible frictional effects , the effect of air column on the pressure change is negligible, the pressure can be assumed to be uniform at a given cross-section of the venturi meter and the flow is horizontal . Air is flowing through a venturi meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, take the air density to be 0.075 lbm/ft. 1. Show that the volume flow rate can be expressed as: 2(P P2) | = A, p(1 – AŽIA}) 2. Find the flow rate of the air? 12.2 psia 11.8 psia Air 2.6 in 1.8 in
a=2 , b=1 The properties of the air in the inlet section with A1 = 0.25ab m2 in a converging-diverging channel are given as U1 = 25a,b m/s, T1 = 3ab K, P1 = 13a,b kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Q(in) is a constant inflow which maintains the water level in the tank. Find the horizontal force needed to hold the tank stationary. If you could make any notes on steps in the method to make it clearer that would be great too. Thanks in advance!
1. Air enters a nozzle at 2.21 and 30m/s. How much mass is entering the m² system if the orifice is 80cm²?
pump with critical cavitation number 0,08 pumps water to a total head of 60 m and temperature of 15°C (Pv=1707 Pa). If the barometric pressure is 98 kPa, head loss in the suction pipe is 1m. Find the maximum value of static suction lift in meters to avoid cavitation in the pump.
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. (WITH FREE BODY DIAGRAM) CHOICES: A.16.5 psi B.15.5 psi C.13.5 psi D.14.4 psi
Problem 3: Water issues from a hole in a large tank, as shown in the attached figure.Assuming frictionless flow, find L.
A 2-inch diameter hose is conveying water at a flow rate of 20 gpm from point A to point B. The pressure at point A is 40 psi. The elevation at point A is 20 ft above mean sea level (MSL) and the elevation at point B is 18.5 ft above MSL. The hose is 100 ft long. Determine (a) pressure at point B if there is no head loss, (b) pressure at point B if head loss is 1 inch per foot of pipe length. (c) Compare pressure at B with and without headloss - what impact does head loss have?
623
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=4.4, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm 6 m/s 2 m/s 60 cm Liquid
VII. Suppose water is leaking from a tank through a circular hole of area A, at it's bottom. When water leaks through a hole, friction and contraction of the stream near the hole reduce the volume of the water leaving the tank per second to cAp 2gh where c(0