Answered: Water in a tank is pressurized to 140…

Name: Water in a tank is pressurized to 140 cm Hg, as shown in the figure.D
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Water in a tank is pressurized to 140 cm Hg, as shown in the figure.Determine the hydrostatic force per meter width on panel AB.Open endWater20°C140 cm4 mHg20°C3 ms.g.=13.6B121.257 kN851.273 kN909.308 kN89.789 kN1031.01 kN405.235 kN722.212 kN600.018

Engineering

Mechanical Engineering

Water in a tank is pressurized to 140 cm Hg, as shown in the figure. Determine the hydrostatic force per meter width on panel AB. Open end Water 20°C 140 cm 4 m Hg 20°C 3 m s.g.=13.6

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The quarter-circular gate of the Figure is 4 ft wide (in the direction normal to the screen/paper). Its radius is R= 7.0 ft and the bottom of the gate is 15 ft below the water surface (D= 15 ft). Determine the force on the stop B. The gate is hinged at A and is made of a material with specific gravity of 2.5. A Water D R B
1,2 m Kablo A semicircular 0.6 m radius water gutter consists of two symmetrical parts hinged to each other at point A at the base, as shown in the figure. The two parts of groove are held together by a cable placed 4 m apart along the gutter. Calculate the pulling force on each cable if the groove is full. Psu = 1000 kg / m ^3
Air P Question 5. 1,2 m wide AB gate is articulated from point A shown in the figure. The heights of the fluids are 6 and 2 for h1 and h2, respectively. Water A hi Considering the measured pressure P = -15 kN/m?, find the magnitude of the force Oil h2 *(kN) that will affect point B, in which the в force provides the balance in AB gate (SGoil = 0,75). Figure 5
Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the figure. Unit Weight is 9.81 kN/cu.m. R = 6.5 ANGLE = 65 RADIUS ANGLE 212.562 79.254 241.707 122.813
Figure AB Cover rests on a flat surface. Cover 180 kg weight and 1.2 m wide. At what height is the water depth the lid won't open? find it. (glycerin density is 1260 kg/m3 , That density 1000 kg/m3 )
Problem 3 A gate is 1.5m in width and hinged at point A. Another point on the gate, B, is resting against a smooth wall. What is the total hydrostatic force (due to the seawater, SG=1.03)? What are the reactions on points A and B, neglecting the weight of the gate? [21 8kN, 180KN, 191KN) Seawater Wall SG-1.03 gate 2m 3m Hinge
A rectangular gate of width "a", length "b" and inclined at an angle "A", with water on one side is shown in the figure. Use a=9.5 ft, b=5ft, z=6.5ft and angle A=55 degrees. (a) Determine the location of the center of the gate from the water surface along the plane of the gate (in feet). (b) Determine the eccentricity (in feet). (c) Determine the location of the center of pressure from the water surface along the plane of the gate (in feet). (d) Determine the vertical distance (in feet) of the center of the gate from the water surface. (e) Determine the total resultant force (in lb) acting on the side of the gate.
Smwidth x Sm leng th The plate used to support the water as shown in Figure Q1 (c) is a S sn square. The value of h is 4.5 m. Ignore the atmospheric pressure, determine the tension of the горе, Т. (c) T Rope h 450 Figure QI (c)
1. A metal plate determined by y = x2 submerged in water as show. Find the total hydrostatic force on 16 the plate. You may leave the density of water as p and gravity as g. Give exact answer. (20,25) Gusten Lo woter level metal plate 16
QUESTION 1 Determine the resultant hydrostatic force on the 1 m square door shown in the figure below, and the force F required to open the door. P = 0.05 MN/m² Po Gas 2 m F -Door -hinge T Water Gas Mercury- Figure 1 500 mm
1. Calculate the horizontal and vertical hydrostatic forces on the curved surface ABC in the figure to the right. с
(c) Determine the magnitude and location of the resultant force acting on the vertical wall shown using pressure prism concept (width = 1.0 m). What is the limitation of using this concept? Patm 1.0 m Oil (0.9) Water (1.0) 1.5 m