Answered: Water flows thru a 10 cm diameter. 100…

Water flows thru a 10 cm diameter. 100 m long connecting two reservoirs with an elevation difference of 40 m, the average velocity is 6 m/s. Neglecting minor losses, the friction factor is:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Water flows through a horizontal 60-mm-diameter galvanized iron pipe at a rate of 0.021 m³/s. If the…

Q: Water flows upward through a vertical pipe of diameter 5 cm and height 10 m. For a constant…

A: Dia of vertical pipe = 5 cmHeight = 10 mPressure head at lower end of pipe = 20.4 mTo Find :The head…

Q: 2. A homogenous cylinder (SG = 0.7) has a diameter of 0.5m. If a 200ON load will make the cylinder…

Q: A large cylindrical reservoir needs to be filed with water after it was drained for maintenance. The…

A: Discharge: The measurement of any fluid with respect to time is known as Discharge. It is…

Q: Two pipes are connected in parallel between two reservoirs A and B. The diameter, length Statement…

A: Dia of pipe 1 = 10 cmLength of pipe 1 = 1000 mCoefficient of friction for pipe 1 = 0.02Dia of pipe 2…

Q: (c). Water at 28°C flows at the rate of 1200 L/min from a reservoir as shown in Figure 6. Calculate…

Q: Question No. 18 A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between…

A: Given data- Length of pipe L=2 km, Diameter of pipe D=0.2 m, Head of water H=8 m, Friction factor…

Q: Flow Between pipes A viscos flow is taking place b/w the two horizontal parallel fixed plates which…

A: Given- Distance between plates B= 80 mm, Maximum velocity umax=1.5 m/s, Dynamic viscosity- μ=1.962,…

Q: the coefficient of permeability = k = 5x103 cm/sec, determine the following:

Q: 6.88m. Darcy-Weisbach friction factor for all pipes, f=0.0238. Pipe 1: Length=3500m…

Q: Three pipes, Pipe A of 300 m and 30 cm diameter followed by Pipe B of 150 m and 20 cm diameter…

A: The difference in the elevation of the two reservoirs, h = 10m Pipe Length, m Diameter, cm…

Q: Compute the pressure at point B

Q: ... T A 30° 2.5m Water hinge L = 2m In the figure shown, a quarter circle gate AOB is hinged at…

A: Water pressure resulting from a liquid flowing on submerged surfaces is what causes hydrostatic…

Q: A horizontal, circular pipe connects two big reservoirs, 1 and 2. The length of the pipe is 100 m.…

Q: A 28 cm diameter pipe exits a reservoir as shown. What is the pressure head at Point 2?

A: Given Given:A 28 cm diameter pipe exits a reservoir as shown. To determine: Pressure head…

Q: 1) Sea water stands in a glass tube of 7 mm diameter at a height of 20 mm. What is thetrue static…

Q: 3m 9m W2 8m W1 6m

Q: A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels in…

Q: SITUATION B. An open tank containing brine (SG = 1.3) is accelerated vertically at 7.5 m/s2.…

A: Given data:- Specific gravity of brine, SG = 1.3 Accelerated vertically at 7.5 m/s2

Q: A dam is triangular in cross-section with the upstream face vertical. Water is flushed with the top.…

A: Pressure is generally the amount of force that is applied perpendicular to the surface of the dam of…

Q: need the answer quickly

A: Given- coefficient of permeability K = 0.06 cm/secSaturated unit weightγsat=19.8 kN/m3

Q: Determine the total hydrostatic force (N) in an inclined, rectangular gate 0.14 m width with oil on…

Q: Q: The concrete dam shown in Figure is constructed on a soil with coefficient of permeability k=0.05…

Q: Q2. Determine the pressure at the bottom of the reservoir if you know that the height is 10 m, width…

Q: A 25 cm circular pipe carries 2536.06 gpm of water under a pressure of 200 pa. The pipe is laid at…

Q: A concrete dam is triangular in cross section and 30 m high from the horizontal base. If water…

Q: A syphon of diameter 200 mm connects two reservoirs having a difference in elevation of 15 m. The…

A: Given- Diameter of syphon d=200 mm, Difference of elevation of two reservoirs=15 m, Total length of…

Q: Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 895.55 L/min from…

A: Calculate the velocity of flow as follows. v=QA=895.55×10-360×6.793×10-3=2.2 m/s Calculate Reynold's…

Q: A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels in…

Q: 1. 15C water is flowing through the tube shown in Figure 1 below at a rate of 0.20 m^3/s. If the…

A: Discharge of water in pipe, Q =0.2m3sPressure at section 1, P1 =415 KPaPressure at section 2,…

Q: A vertical pipe system shown in the Figure below, d = 300 mm throughout, carries 0.82 (m³/s) of…

A: ###Calculation of pressure drop between A and B when B is 100 m higher than A in Given pipe system…

Q: Two Water flows from reservoir A to reservoir B through two pipes as shown below. Determine 1) the…

A: Given data: Assume α = 1.0 It is asked to determine : 1) the discharge in the pipe 2) the…

Q: Water flows through a horizontal pipe with a cross-sectional area of 5m^2 at a speed of 6L/sec. With…

Q: A pipe carrying water tapers from cross section 0.5 m² at A to 0.2 m² at B. The average velocity at…

A: Cross sectional area = 0.5 m2 ar A and 0.2 m2 at B.The average velocity at A = 2 m/s and Pressure =…

Question

Water flows thru a 10 cm diameter. 100 m long connecting two reservoirs with an elevation difference of 40 m, the average velocity is 6 m/s. Neglecting minor losses, the friction factor is:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

6. Determine the critical height of the water level that causes the concrete gravity dam to be on the verge of tipping over. Assume water also seeps under the base of the dam and produces a uniform pressure under the dam. The density of concrete is pc = 2400 kg/m³. Hint: Work the problem using a 1-m width of the dam. 18 m h -6m
Need asap pls.
Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a diameter of150mm. Determine the head loss due to friction using Manning’s formula with n = 0.012.
Two reservoirs, A and B, are 7.5 km away from each other and connected by a 900 mm steel pipe ( f = 0.02). If reservoir A is 10 m higher than reservoir B, the pressure at B is 90 kPa greater that the pressure at reservoir A, what is the amount and direction of flow of water in the pipe. Use f = 0.02.
Why clamp handles are used?
Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 896.61 L/min from the reservoir and through the pipe shown in the Fig. below. Compute the pressure at point B, considering the energy loss due to friction, but neglecting other losses. Also, use pipe roughness of 1.50 X 10-6 m. Hint: Use the appropriate formula to determine the friction factor, f to 4 decimal places (flow type dependant); g = 9.81 and round off to 3 decimal places for all other step calculations leading to the final answer including the final answer.
2021-2... ents on A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water is 1.50 m above the top of the gate. Compute the distance of the center of pressure from the centroid of the gate. 1.50 m O 0.1068 m O 0.0871 m O 0.1381 m O 0.0943 m 2.00 m
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0.15 m3/s and 0.25 m/s respectively. If the coefficient of friction for the three pipes is 0.008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. hA h8 L2, D2 L1, D1 L1 = 1000 m L2 = 1500 m L3 = 2000 m D1= 200 mm D2 = 250 mm = 400 mm L3, D; hc %3D D3 = Figure 1: A three reservoirsystem
- once answered correctly will UPVOTE!!
k=10^-3 ft/min Find: a) Seepage beneath the dam (ft/min) b) Pressure head at points A and B b) Pore water pressure at points C through K (in psf) f 570 ft. EL. 780 f (coeff. of friction) 0.35 50 ft. 280 ft Yconc 150 er 180 ft. 7 EL. 600 380 ft 170 ft. EFGHL K. 170 ft. silty SAND .Y Ysat 120 pef k- 10-3 /min