Water flows through the elbow. It exits to the atmosphere at section 2. The inlet and exit pipe diameters are D1=10 cm and D2-3 cm, respectively. At a weight flow rate of 169,9 N/s. The elevation difference between the inlet and outlet sections is 25 cm. Neglecting the weight of water and elbow, estimate the force [N] on the flange bolts at section 1. (NOTE: Pwater=998 kg/m3)

Water flows through the elbow. It exits to the atmosphere at section 2. The inlet and exit pipe diameters are D1=10 cm and D2-3 cm, respectively. At a weight flow rate of 169,9 N/s. The elevation difference between the inlet and outlet sections is 25 cm. Neglecting the weight of water and elbow, estimate the force [N] on the flange bolts at section 1. (NOTE: Pwater=998 kg/m3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the flow illustrated in the figure below, the speed at point A is equal to 20 m/s. Neglecting energy losses and assuming uniform flow, determine the pressure PC.
Water enters a shower head through a pipe of internal radius r = 6.4 mm, and leaves through 30 small holes, each of radius r1 = 0.08 mm. When the faucet is opened, the water moves in the tube at a speed of 90 cm/s. What is the volumetric flow of the shower head in liters per second?
Question is a fluid mechanics
help
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20 m. Total energy head of water at a point is 26 m. The Discharge (L/s) of water through the pipe is
A large tank is partly filled with oil (s.g.= 0.85), the air space above being under pressure. A 50 mm ϕ hose connected to the tank discharges on the roof of a building 15.25 m above the level in the tank. The friction loss is 5.50 m. What air pressure in KPa must be maintained in the tank to deliver 0.0124 m3/s on the roof?
= = Air flows radially outward between the two parallel circular plates shown in the figure below. The pressure at the outer radius, Ro 5 cm, is atmospheric. Find the pressure at the inner radius R¿ 0.5 cm, if the air density is constant, the air flow is inviscid, the volume flow rate is 4.0 L/s, and the plate spacing is h = 0.125 cm. h Po= Patm = 101.3 kPa T = 20°C 777 R₁ Ra
Fast pls i will give u like for sure solve this question correctly in 5 min pls A reduced bend in a pipe is used to divert the flow of water (p=1000 kg/m³) at a rate of 35 kg/s. The discharge of the fluid is to the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the outlet. The elevation difference between the centers of the exit and entrance is 40 cm. The mass of the cubit and the water it contains is 60 kg. The center of mass of the fluid assembly and elbow is located 50cm horizontally, with respect to the flange. Consider a flow correction factor of n=1.04 for eq. of linear momentum. Determine: a. The pressure at the entrance of the elbow. b. The net anchorage force in the flange required to hold the elbow in place. c. The moment generated in the flange from the applied forces
Q4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁=30cm D₂=20cm 6 Q4 1.5
Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for P1, P2 and p3, respectively, what are the head loss between 1-3 in meters.