Water flows through the 200-mm-diameter pipe bend with a velocity of 11 m/s and discharges into the atmosphere at B. The mass of the pipe bend and the water within it is 25 kg, having a center of gravity at G. 600 mm 450 mm 200 mm Part A Determine the r-component of force acting on the coupling at A.

Water flows through the 200-mm-diameter pipe bend with a velocity of 11 m/s and discharges into the atmosphere at B. The mass of the pipe bend and the water within it is 25 kg, having a center of gravity at G. 600 mm 450 mm 200 mm Part A Determine the r-component of force acting on the coupling at A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

: Water Flow into horizontal pipe with velocity of v. Determine the horizontal and vertical component of force and the moment at A need to hold the elbow in place. Neglected the weight of the elbow and the water within it . Take v between 1 to 5 m/s and D1 between 0.2 to 1.0 m and D2 between 1.0 to 0.2 m. 3 m D1 v1 A В
Water flows steadily from a tank mounted on a cart. After the water jet leaves the nozzle ofthe tank, it falls and strikes a vane attached to another cart. The cart’s wheels are frictionless,and the fluid is inviscid. Determine the tension in ropes A and B.
Water is discharged into the atmosphere from the pipe at 15 m/s. Neglect the resistance provided by the pipe at C, and the weight of the pipe and the water within it. 100 mm 300 mm 60 mm 150 mm Part A Determine the horizontal component of force that is developed at the fixed support A by the ground in order to hold the pipe in equilibrium. Express your answer to three significant figures and include the appropriate units. Enter positive value if the direction of the force is to the right and negative value if the direction of the force is to the left.
6. A small particle is placed inside the frictionless, semicircular tube of radius R shown in the figure below and released. Using angular momentum methods, show that the particle's equation of motion is given by Ö + (g/R) sin(0) = 0. Hint: Start with dHo/dt = EM₁ e
Problem 2 - Determine the greatest possible mass flow through the nozzle if the throat has a diameter of 50 mm. The air in the reservoir has an absolute pressure of 400 kPa and a temperature of 30°C. I mm
The fire boat discharges two streams of seawater, each at a flow of 0.35 m^3 and with a nozzle velocity of 40 m/s Determine the tension developed in the anchor chain, needed to secure the boat. The density of seawater is ρsw = 1020 kg/m^3
While travelling on a dirt road, the bottom of a car hits a sharp rock and a small hole develops at the bottom of its gas tank. If the height of the petrol in the tank is h=h= 31 cmcm, determine the initial velocity of the petrol at the hole. Given that there are no minor or major losses and density of petrol is ρ=ρ= 778 kg/m3
The water jet discharging from the orifice with velocity VA equals 6.264 m/s, Determine the vertical distance y and the velocity of the water when it strikes the ground at B. y B 3.46 m
The offset nozzle has a discharge area A at B and an inlet area Ao at C. A liquid enters the nozzle at a static gauge pressure p through the fixed pipe and issues from the nozzle with a velocity v in the direction shown. If the constant density of the liquid is, write expressions for the tension T, shear Q, and bending moment M in the pipe at C. If Ao
Given the velocity through the exhaust of the rocket is: U(r) = Umax (1-1) 1¹/² R Umax is a constant r is the radial coordinate out from the center of the engine R is the outside radius of exhaust flow Determine the reaction force of the exhaust in terms of: p, Umax, and R
Water is discharged into the atmosphere from the pipe at 14 m/s (Figure 1). Neglect the resistance provided by the pipe at C, and the weight of the pipe and the water within it. 100 mm B 300 mm 60 mm 150 mm A Determine the horizontal component of force that is developed at the fixed support A by the ground in order to hold the pipe in equilibriu Determine the vertical component of force that is developed at the fixed support A by the ground in order to hold the pipe in equilibrium. Determine the moment that is developed at the fixed support A by the ground in order to hold the pipe in equilibrium.
Water is drawn into the pump, such that the pressure at the inlet A is -30 kPa and the pressure at B is 120 kPa The pipe has a constant diameter of 100 mm Take h = 4 m. Part A If the discharge at B is 0.25 m /s, determine the power output of the pump. Neglect friction losses. Express your answer to three significant figures and include the appropriate units.