Water flows through a Venturi meter as shown below. Determine the discharge coefficient, Cd, of the Venturi meter if the actual discharge is determined to be 2.104 cfs. Use D1 = 12.07 in., D2 = 4.06 in., y = 8.26 in. Points 1 and 2 are centerlines of the inlet and throat, respectively. Round off to five decimal places.

Q: difference in height between the two legs of 30 in. If the meter coefficient is equal to 0.975,…

A: ###Determination of Actual Discharge ###

Q: PROBLEM 5 Consider a steel pipe of inside diameter of 10.02 in having in it an open globe valve (K =…

A: Given, Diameter of the pipe D =10.02 in =0.835 ft. Length of the pipe L=100 ft. Discharge Q=5…

Q: 200mm 300mm diameter 450mm 30° 400mm 1 Mercury diameter (SG = 13.6) "X" 350mm Water In the 200mm…

A: There manometer attached with the venturi meter  now we determine value of "X"

Q: The volume of water through 15 second is 315 mL, the diameter of the orifice meter is 6mm, and the…

A:

Q: 450 mm 150m -0. 375 mm Mercury S = 13.6

A: Given data Diameter of inlet= 450 mm  Diameter of throat = 150 mm  Specific gravity of mercury =…

Q: Problem A horizontal venturimeter with inlet and throat diameters 30 cm and 15 cm respec- tively is…

A: Given Diameter at inlet D1=30 cm, Diameter at throat D2=15 cm, Reading of differential manometer…

Q: Using the information and the following data that were collected for two verticals in a stream at a…

A:

Q: In the context of a sewer system, your objective is to find the optimal slope (SS) of a pipe to meet…

A:

Q: A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a…

A:

Q: 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines…

A:

Q: Moving to another question will save this response. Question 47 A pipe has a length of 462 m., and a…

A:

Q: Q4:Compute the stream flow (discharge)in (m/sec) for the measured data below, use a-0.03 and…

A:

Q: Triangular notch with vertical angle of 90° measures a flow rate. If the value of Cd = 0.6 and there…

A: Given: Coefficient of discharge, Cd = 0.6 Error in measurement of head, dH = 2.5 mm Discharge, Q =…

Q: Given the data below, design a section of sanitary sewer to carry these flows at a minimum velocity…

A: minimum velocity of 0.6 m/s, n=0.013 minimum cover above the sewer pipe is 1.5m

Q: Q Put a Circle around the CORRECT Answer. 1- If the secondary open drain collects water flow from 31…

A: Multiple choice questions are given. We need to make correct choice

Q: With the empirical equations below, derive for the head loss equations with respect to discharge.…

A: ANSWER : OPTION a) hf=fLv22gD   Rewritten as -->.  hf=8Q2fLπ2gD5 where Q - discharge f - friction…

Q: How to calculate discharge through a venturimeter if the outer and inner cross-sections are given,…

A: Given: Outer cross-section = A1 Inner cross-section = A2 Difference in the height of manometric…

Q: flows through a Venturi meter as shown below. Determine the discharge coefficient, Cd, of the…

A:

Q: 2/ Put a Circle around the correct Answer: 1/ Dimensions of discharge coefficient Cd are: (a)…

A:

Q: Compute the discharge of water through a standard sharp edge orifice 25mm in diameter under heads of…

A: Discharge of water through standard sharp edge orifice is given by ; Q = A × V where ; A = Area V =…

Q: Avoid truncation in the middle of solution. Thank you Water flow through a 3 in diameter pipe at a…

A: Given data in question  Diameter  Velocity  To find out  Discharge

Q: Given: f= 0.02 for all pipes, Determine discharge in each pipe if total head loss is 20m. L1 = 250…

A:

Q: Situation 16 - The flow of water from Reservoir A shown is 600 L/s. Properties of the system are as…

A:

Q: 6. Oil is flowing upward through a Venturi meter as shown. Assuming discharge coefficient of 0.93,…

A: Given data in question  Oil specific gravity 0.82 Glycerine specific gravity 1.26 Diameter 500 and…

Q: 3. Determine the discharge of water through the 50-cm steel (Wrought iron) pipe shown in the figure…

A: Given that : Diameter of steel pipe = 50 cm Determine the discharge of water through 50 cm steel…

Q: 1. A liquid (sp gr 2.0) is flowing in a 50 mm diameter pipe. The total energy at a given point is…

A:

Q: DATA, RESULTS, AND COMPUTATIONS Diameter of Orifice = 2mm Table 12.1 Constant Head Results Head, h…

A: a (area of orifice) = π/4*0.0022 = 3.1416*10-6 m2

Q: Referring to the figure below, the tank is being filled with water by two one- dimensional inlets.…

A: As the flow is unsteady, we can apply continuity equation in the control volume.

Q: Using Hardy cross method find out the flow rates of the circuit shown assuming a friction factor f =…

A:

Q: Q. For the parallel pipe system shown, the flow discharge of water within the system is ........…

A: ###Computation of flow rate through each branch of the loop####

Q: A discharge of 100 L/s to be measured by triangular notch of vertex angle 60°. What would be the…

A:

Q: El. 90 m A El. 75 m El. 50 m El. 30 m D Line 3: 45um - 300mm Line 4: 900m - 150mm 600m - 600mm Line…

A:

Q: Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. O 0.197…

A:

Q: . A tank with a horizontal sectional area constant at 10m² and 4m high contains water to a depth of…

A:

Q: The three-cistern system in the figure contains water. If L1= 2000 m, f 1= 0.013, D1 1m- L2 = 2300…

A: The length, diameter and the friction coefficient of each pipe is given. Q3=Q1+Q2     ...(1) The…

Q: 300 mme 100 mmØ HeO, 500mm A 100mm diameter venturi meter is installed in a 300mm diameter…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.