Water flows steadily from a large tank and exits through a vertical, constant diameter pipe as shown. The air in the tank is pressurized to 50 kN/m^2, determine a)the height h, to which the water rises, b) the water velocity in the pipe, and c) the pressure in the horizontal portion of the pipe.

Water flows steadily from a large tank and exits through a vertical, constant diameter pipe as shown. The air in the tank is pressurized to 50 kN/m^2, determine a)the height h, to which the water rises, b) the water velocity in the pipe, and c) the pressure in the horizontal portion of the pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1) By using dimensional analysis concept, express the wall shear stress for the pipe flow which is depending likely on the distance from the beginning of the pipe, pipe diameter, pipe wall roughness, fluid velocity, density and viscosity?
You and a friend plan to throw one end of a hose over a tall fence to siphon water from your side to the other side. Your friend says it doesn't matter how high the fence is, it will always work as long as your end of the hose is higher than the other side. However, you remind him that isn't actually true. What is the potential problem and about how high can the fence be (in meters) before it becomes an issue?
5. Consider two tanks, A and B, each with a large opening at the top. The two tanks contain different liquids. A small hole is made in the side of each tank at the same depth h below the liquid surface, but the hole in tank A has three times the cross-sectional area of the hole in tank B. (a) If it is known that the mass flow rate is the same for the two holes, find the ratio of PALPB of the densities of the liquids in tanks A and B. (b) (c) equal volume flow rates, what height above the hole must the liquid in tank A be just then? Find the ratio RVAIRVB of the volume flow rates from the two tanks. At one instant, the liquid in tank B is 90 cm above the hole. If the tanks are to have
Pls do stepl by step solution. Show me how to convert l/s to m/s and all steps. Thank u very much
.A hydraulic pump delivers 13.5 litres per minute towards pressure of 310 bar.Find the following (a) Calculate the hydraulic power in kW (b) If the overall efficiency of the pump is given as 63% .Find the input of electric power needed to drive the pump in watts (a) The hydraulic power (in kW) = (b) The power of electric motor needed to drive the pump (in W) =
Q2. Design and plot a hydraulic system for drive and control aircraft flap to overcome 500 N aerodynamic forces with the following specifications:- The actuator single acting cylinder with bore diameter 25 cm , smooth pipes line has diameter and total length 15 mm and 12 m respectively, six elbows (K = 0.9), if average velocity of the oil in the pipes 20 m/s and total pressure losses across control valves and other accessories 1.4 bar. Determine total pressure pump required for hydraulic circuit. (Note:- poil =880 kg/m², voil= 64.2 mm/s)
At the end of a production line at Danfoss, a 40 kg box of thermostats with speed 3 m/s is colliding with a 10 kg box at rest. What is the common speed of the two boxes right after impact?
1.1. The pump whose performance curves are shown in Figure P1.1 is operated at 1750 rpm and is connected to a 2-in. i.d. galvanized iron pipe 175 ft long. What will be the flow rate and power input? 100 90 Head curve 80 70 60 50 40 -Efficiency 30 20 10 20 40 60 80 100 120 140 160 180 Flow rate (gpm) FIGURE P1.1 Performance curves for a pump with a 9-in. impeller and speed 1750 rpm. 1.7. If the pump and pipe arrangement of Problem 1.1 now includes an elevation increase of 30 ft, what flow will result? Head rise (ft); efficiency ()
Must answer all the four questions. Otherwise i will dislike it.
Imagine the water level in the tank as shown in the Figure rises at a rate of 0.004579 ft³/sec. then find: i) The volume flowrate of water leaving the tank (Q3) in ft³/s from pipe 3. ii) The average velocity of water leaving the tank (V3) in ft/s from pipe 3. Pipe 1: Qi=0.0109 ft²/s Pipe 2: Q₂ = 0.025 ft³/s Pipe 3: dy = 1.5 in. V₁ = ?! Q₁ =?
I am having trouble with units on this problem I am pretty sure I have the right number but I am unsure about the units
Flow Through Pipes A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe in Liters/sec, if diameter of pipe is 0.5 m Take all losses into account. Assume f = 0.01.