**Transcription for Educational Website:**---**Water Flow Analysis: Pipeline Discharge****Problem Statement:**Water flows from a reservoir through a pipeline as illustrated in the diagram below. The flow is considered frictionless and discharges freely at point C.1. **Question (a):** What is the total head (total specific energy) at point A?2. **Question (b):** What is the total head (total specific energy) at point B?3. **Question (c):** What is the discharge velocity at point C?**Diagram Explanation:**The diagram shows a reservoir connected to a horizontal pipeline. The water level in the reservoir is marked at point A. The pipeline starts at point B inside the reservoir and extends horizontally to point C where the water discharges. The vertical distance from point B to the water level at point A is 150 feet (45.7 meters). ---This diagram and problem help in understanding concepts of fluid mechanics including total head and discharge velocity in a frictionless flow system.

Answered: Image /qna-images/answer/662beca1-a38c-4f33-a84f-4a4999fd9339.jpg

Water flows from a reservoir through a pipeline as shown in the following diagram. The flow is considered frictionless and discharges freely at point C. (a) What is the total head (total specific energy) at point A? (b) What is the total head (total specific energy) at point B? (c) What is the discharge velocity at point C? A 150' (45.7 m) B

Water flows from a reservoir through a pipeline as shown in the following diagram. The flow is considered frictionless and discharges freely at point C. (a) What is the total head (total specific energy) at point A? (b) What is the total head (total specific energy) at point B? (c) What is the discharge velocity at point C? A 150' (45.7 m) B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(c) Liquid flows through an orifice in the bottom of a cylindrical tank at a velocity of 4m/s. If the jet diameter is 2.5cm, what is the rate of flow in lit/sec? If the tank is 25cm in diameter, at what rate is the liquid surface falling?
URGENT PLS
Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter section of the piping system is 5 m/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in L/s. For the case of steady flow of water through the piping system, what is the average speed of water in the 300-mm-diameter section of the system?
Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the energy and hydraulic grade lines. water 10m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel)
Water at 50°F is pumped from a lake at 750 gpm through a length of 3-inch schedule 40 commercial steel pipe as shown below. The inlet to the pipe is eight feet below the surface of the lake. A 25-HP gasoline engine drives the pump and the pump has an efficiency of 80% What is the Reynolds number in the pipe? Is the flow laminar or turbulent? What is the head added to the water by the pump? What is the head loss due to pipe friction?
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
QUESTION 5 Q2. Two water pipelines converge into one line of 2.5m diameter. a). What is the velocity of water flowing in the converged line if the discharges and diameters of the converging lines are 1 m3/s with an 800mm pipe and 0.5 m³/s with a 500mm pipe? (m/s) b). What is the mass flowrate under these conditions? (kg/s) c). What percentage change in velocity would there be in the converged pipe if the diameter of the pipe was reduced by 20%? Take the density of water to be 103 kg/m3. Part a). is denoted Q5, part b). as Q6 and part c). as Q7
PLEASE HELP ME ANSWER THIS ASAP. NOTE: COMPLETE SOLUTION WITH PROPER FIGURES. 3 DECIMAL PLACES
Civil engineering -Hydraulics