Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in which the pressure is reduced and electricity is produced. The shaft power input to the pump is 1 KW snd the shaft power output the turbine is 1 kW. Both the pump and turbine are 90% efficient. If the elevation and velocity of the water remain constant through out the flow and irreversible headloss is 1 m, the pressure of water in kPa at the turbine exit is

Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in which the pressure is reduced and electricity is produced. The shaft power input to the pump is 1 KW snd the shaft power output the turbine is 1 kW. Both the pump and turbine are 90% efficient. If the elevation and velocity of the water remain constant through out the flow and irreversible headloss is 1 m, the pressure of water in kPa at the turbine exit is

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501…

A: mass flow rate (m.)= 200 kg/h= 200 kg/3600 sec= 0.0555 initial temperature ( Ti)= 501 C speed (C1)=…

Q: A pump supplies water at a flow rate of 4ft3/s from an open reservoir through a horizontal 8-in…

A: Head loss alludes to an estimation of the energy disseminated in a liquid framework because of…

Q: Find the power of motor needed to pumped the water at a head of 100m at the rate of 400 lps if pump…

Q: A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450…

A: Given data,mass flow rate m= 500 kg/henterring pressure P1=44 atmtemprature T1=450°CVelocity of…

Q: 1. A turbine is fed from a mountain reservoir 300 metres above it. Calculate the drop in…

A: The objective of the question is to calculate the drop in mass specific energy and the volumetric…

Q: Water from a reservoir is pumped over a hill through a pipe 900 mm in diameter and a pressure of one…

A: Given:Pipe diameter, d=900 mm=0.9 mPressure at the pipe discharge, P2=1 kg/cm2=1*98.1 kPa=98.1…

Q: Aa hydraulic turbine receive water from a reservoir at elevated of 50 m above it. What is the…

Q: You are asked to calculate a rotadynamic pump with a total manometric head of 11 mss and demand flow…

A: Given Data⇒ Total manometric head(h)=11 m Flow is Q=19LitsSInce 1Lits=1000m3shenceQ=0.019m3s The…

Q: A pump with an efficiency of 15mm% is used to pump water from a tank (stationary water inside) at…

Q: Q3: Two tank are connected with piping system as shown. If the pump chara given by: hp- 31-120000…

Q: 5. The horizontal pump in the Figure discharges 10°C water at 35 m/h. Neglecting losses, what power…

Q: A water pump generates a maximum pressure of 89000 Pa with a speed of 5 m/ s, does this water pump…

A: Given:- ∆P = 89000 Pa V1 = V= 5 m/s V2 = 0 m/s Z1 = 0 m Z2 = h m To Find :- Maximum height

Q: A centrifugal pump(efficiency 86%) lifts water through a total height of 42m from reservoir to…

Q: A pipe equipped with a nozzle is used to deliver water to the wheel of a hy draulic turbine. The…

A: Given: Diameter of the nozzle→d=10 Cm=0.10 m so the area of the nozzle→a=π4d2=π40.12=0.0078 m2…

Q: The pressure of 200 kg/s of water is to be increased by 4MPa. Thw water enters through a 20cm…

A: Given data, m= 200 kg/s D=20cm =0.2 m ---> A= π0.2*0.2/4 = 0.0314 m2 d= 12cm =0.12 m ---> a=…

Q: A pump delivers 1500 L/min of water at 20°C against apressure rise of 270 kPa. Kinetic and potential…

A: Given: The volume of water delivers by the pump is V=1500 L/min. The rise in pressure by the pump is…

Q: A turbine is discl ging 10 m³/s under a head of 22 m at 200 rpm. The efficiency is 90%. Determine…

A: Given that, Q1=10 m3/s, H1=22 m, N1=200 rpm, ηo=90 %=0.9, H2=44 m

Q: 30m T -2 75cmØ

A: Given data: The diameter value is, d=75 cm=75 cm×1 m100 cm=0.75 m. The power developed by the…

Q: A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at…

A: Flow rate (Q) = 7 m³/s, Height (H) = 10 m, CQ=0.15 CH=6 CP=0.75.To find:Pump impeller diameter…

Q: The exit flow angle of stator in an axial steam turbine is 68°. The flow angle of the relative…

Q: The net head influence to a Caplan turbine is 45m. the working fluid hits the rotor and the rotor…

Q: A centrifugal pump operating under steady flow conditions delivers 2275 kg/min of water from an…

Q: A centrifugal pump is to be placed at the bottom of a vertical shaft 350 m deep to deal with an…

A: Given data depth of shaft = 350 m In flow of water = 22 l/s = 22 x 10-3 m3/sPower rating of the…

Q: A rection turbine has guide vane angle 30° the runner blades make an angle of 80° relative to the…

A: Given data: α=30°β=120°N=16.67 rpsη=88% Need to determine the runner diameter at inlet and the…

Q: find the vane angles at inlet and outlet. Show schematic diagram and provide solutions.

Q: A 650 bhp Diesel Engine with 6 cylinders has a brake thermal efficiency of 36 % and a jacket water…

A: Given : P = 650 HP = 650*0.7457 KW n = 6 ηₜ = 36% Lw = 27 % = 0.27Q dTw = 12⁰C dTc = 5 ⁰C

Q: A pump rated at 700W is used to transfer water from an open tank at ground level, to another open…

Q: Water from a reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 1…

A: The diameter of the pipe is d=450 mm. The pressure at the summit is P=1 kg/cm2. The height of the…

Q: Derive the equation for turbine and nozzle with the help of steady energy equation by stating their…

A: Nozzle is a device that accelerates the fluids. Assumptions of Nozzle - Steady-state process-…

Q: The power developed by the pump is 30kw. What is the percent decrease in power if speed will…

Q: Identify what is the system in this problem and write the general energy balance equation (no need…

Q: A garden hose is connected to raise a narrower hose wherein the diameter of the bigger is twice the…

Q: A steam turbine developed 2372.2 hp when its inlet condition is 1300 BTU/lb enthalphy and 400 ft/s…

A: given data- power developed P= 2372.2 hp mass flow rate = 200 lb/min inlet condition - h1 = 1300…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Include a fre body diagram

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

answer first item only
answer 2nd item only
answer first item only
answer 2nd item only
Water from a reservoir is pumped over a hill through a pipe 900 mm in diameter and a pressure of one kg/cm? is maintained at the pipe discharge where the pipe is 85 m from the pump centerline. The pump have a positive suction head of 5 m. Pumping rate of the pump at 1000 pm is 1.5 m/sec. Friction losses is equivalent to 3 m of head loss. What amount of energy must be furnished by the pump in KW?
Q3: Two tank are connected with piping system as shown. If the pump characteristics are given by: hp- 31-120000 and, 7p--190000Q+8590Q Where hp is in meters and Q in m³/s and np is the pump efficiency (%).Estimate the operational cost of the pumping (10000) m² of water to the upper tank if the cost of IKwh is 2000 ID. Neglecting the minor losses. H=15mm 0-150mm
A garden hose is connected to raise a narrower hose wherein the diameter of the bigger is twice the diameter of the narrower hose. The fluid flowing is a fresh water having an entrance velocity of 1.2 m/s and a pressure of 143 kPa find the the pressure in KPa at the exit point. Note; hor Ay = 20.0 cm 20.0 cm Select one: 138.9 kPa 139.8 kPa 183.9 kPa O 189.3 kPa
In a hydroelectric power plant, water is available at the rate of 180m/s under a head of 18m The overall efficiency of plant is 80%. The number of turbines requircd if the turbine runs at a spced of 150 rpm and have a maximum specific speed of 400 ( Take g=981 m/s")
NOTE THE ANSWER SHOULD BE 10.75m3/s Find the flow rate of water through the sytem shown for the turbine to produce 20 kW. Neglect friction in your calculations NOTE: THE ANSWER SHOULD BE 10.75m3/s
A boiler feed pump has a suction enthalpy of 2500 KJ/kg and exit of 2505KJ/kg. Find the velocity of water in the flowing in the pump. Answer: 100m/s
can you please find solution
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.