Water density =1000 kg/m³ and viscosity is 0.001 N s / m², is pumped between two reservoirs at 0.2m³/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW.

Q: A manufacturer states that their gear pump requires 0.85 hp to pump 9 gpm of oil (sg=0.90) with a…

A: The flow rate of the oil is, Q=9 gpm. The specific gravity of the oil is, SGo=0.90. The total heat…

Q: please explain how to get the friction factor

A: The objective of the question is to calculate the friction factor, the power supplied to the pump,…

Q: A reservoir like the one shown has SAE10 oil at 20 C and is connected to a capillary tube for…

A: Neglect major and minor losses

Q: Q3:- A liquid whose coefficient of viscosity is µ flows below the critical velocity for laminar flow…

A: The loss of pressure in a length of 120 m is 11520 N/m2.

Q: A 2-inch copper pipe connection was made from the basement to the second floor in the building. The…

A:

Q: Find the head lost due to friction in a pipe of diameter 5 mand length 5000 cm, through which a…

A: d=5 m L= 5000 cm ρg=9000 Nm3v=3000 cmsecμ=400 poise or μ=40 N-sm2…

Q: For the water shooting out of the pipe and nozzle as shown in Fig. find 1- the flow rate (Q) through…

A: (1) To find: The flow rate through the pipe. Given: The diameter at A is DA=200 mm. The diameter at…

Q: a pumping station working with a pump head of 25m. the output power of the motor for that pump is…

A:

Q: 4. The pipe system shown in the Figure. The flow rate in pipes AB and FG is 0.88 n'/s. All pipes are…

A:

Q: Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a…

A: The diameter of pipe is d=70 cm=0.7 m. The height of reservoir is h=95 m. The power output from…

Q: Water flows into a house by means of a pipe with an inner diameter of 2,4cm, absolute pressure is…

A:

Q: 5. The large tank shown in the figure is filled with water to a height of ho. Water exits the 5-cm-…

A: Step 1: Step 2: Step 3: Step 4:

Q: For the hydraulic system of Figure, the following data are given: The pump is adding2.984kW to the…

A:

Q: A swimming pool W by Y by h deep is to be emptied by gravitythrough the long pipe shown in Fig. .…

A: Given data:   *The bottom dimension of the pool is W by Y. *The depth of the pool is h. *The average…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 50 cm respectively.…

A:

Q: Consider using a venturi tube to messure the flow rate of water (280c^0) through a pipe   5 cm in…

A: Given: Flow through pipe is measured by venturi meter. Diameter of pipe, d1 = 5cm diameter at…

Q: Water flows from a large close tank, through pipe length 15m, diameter (30mm) and exits with…

A:

Q: Imagine that you are recently bought a 2-floor house and want to improve the water installation at…

A: Given that, Height of top flor from water meter, z2=15 m,Pressure inside the pipe, P=200…

Q: Answer the attached file

A: The diameter of the pipe between pump and reservoir is D1=20 cm. The length of the pipe pipe between…

Q: The power 455 W is required to transmit 8 x 10-3 m3/s of water. Find the loss of head due to…

A: Given Data  Flow rate , Q=8*10-3 m3/s Power =455 watt g=9.81 m/s2. Density of water 1000 Kg/m3.

Q: onsider the hydropower schematic shown below with a lake of 70m elevation above a turbine house.…

A:

Q: each pipe may be taken 0.03. 100 mm diameter, 200 m length Atmosphere B 100 mm diameter, 100m length…

A: Calculated discharge in each pipe.

Q: Q3/ Hydraulic oil ISO 68 is flowing through a hydraulic line with an inside diameter of 1.4 inches…

A:

Q: Q2: The discharge of water inside the pipe is 1 liter/s, the diameter and roughness of the pipe is…

A: Given:Discharge,Q=1litres=1×10-3m3sDiameter of pipe,d=40mm=0.04mRoughness of…

Q: The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated…

A: Given data, Rate of discharge, Q = 200 lps Q = 0.2 m3/s Pressure at A, PA = 206 KN/m2 = 206 x103 Pa…

Q: Design the chilled water pipes system shown in the figure below and find the power of the pump…

A:

Q: 7. A siphon draws oil (sg=0.86) as shown in the figure. Determine the volume flow rate of oil from…

A: Consider 1 is the section in the siphon at the level of oil in the tank, and 2 is the section at…

Q: The power 351 W is required to transmit 2 x 10-3 m3/s of water. Find the loss of head due to…

A:

Q: I need the answer

A: Consider the pump as a reference line and only minor loss will be taken into account.

Q: The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated…

A:

Q: The calculation of power from moving fluid has the following parameters: Volume flow rate = 10 +/-…

A:

Q: Oil flows in a 50 cm diameter pipeline at a velocity of 1 m/s. If the pipeline is 1 km long,…

A:

Q: Find the difference in pressure head and velocity of flow of an oil through a pipe, when the…

A: Write down the given values using suitable variables. Here Cv signifies pitot tube coefficient, s…

Q: Find the cross sectional area of pipe Discharge=77 m3/s Velocity=10 m/s

A: Given data : Discharge Q=77 m3/s Velocity V=10 m/s   Required : Cross sectional area of pipe

Q: essure the flow ra

A: given:

Q: A pipe with diameter 30 cm carries oil of sp.gr. 0.95 at a velocity of 4 m/s .at another section the…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.